Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Memphis Mojo/HIGHS Wiring Help..
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="1000101" data-source="post: 4632296" data-attributes="member: 593073"><p>Ok, no naked sister pic, but it does get a bit more attention for my post..</p><p></p><p><span style="color: Blue"><span style="font-size: 12px">I have a Memphis Belle Amp</span></span></p><p></p><p>RMS Power 4 Ohm Stereo Ch 1-4/Ch 5 (4 ohm Mono) 14.4V….......75 watts x4/300 watts x1</p><p></p><p>RMS Power 2 Ohm Stereo Ch 1-4/Ch 5 (2 ohm Mono) 14.4V………..115 watts x4/600 watts x1</p><p></p><p><span style="color: blue">RMS Power 4 Ohm Bridged Ch 1-4/Ch 5 (1 ohm Mono) 14.4V………230 watts x2/1100 watts x1 </span></p><p></p><p>Input Sensitivity……..250mV-9V</p><p></p><p>Frequency Response +/- 1dB……..10Hz-50kHz/10Hz-650Hz</p><p></p><p>Dimensions 7.6" x 2.4" x……….25.8125"</p><p></p><p>Optional Remote Gain Control…….. MCRG</p><p></p><p><span style="color: blue"><span style="font-size: 12px">I want to run the amp this way</span></span><span style="color: blue">…</span></p><p></p><p><span style="color: blue"><span style="font-size: 14px">RMS Power 4 Ohm Bridged Ch 1-4/Ch 5 (1 ohm Mono) 14.4V………230 watts x2/1100 watts x1</span></span></p><p></p><p><span style="color: Red">It should be sufficient enough to run the 2 15" mojos and then 2x 12" M3's. the mojo's have an rms rating around 1,000wtts and the M3 is 400 rms. so if I push 230wtts to each M3 and about 550 watts to each mojo. This should be just fine enough…right?</span></p><p></p><p>This sounds great and all, but I’d rather just run 2 Mojos and use the other channels for my mids/highs… any advice on how to wire this.. <span style="color: blue">are there any component/mids/highs out there that can handle lots of power.. </span></p><p></p><p><span style="color: blue"><span style="font-size: 12px">It seems like I can only run the amp as a 3channel or 5channel and I definetly want to run 2 Mojos at 550wtts each.. but the remaining 230wtts need to be for highs.. what do I do.. just turn the gain way down</span></span><span style="color: blue">?</span></p></blockquote><p></p>
[QUOTE="1000101, post: 4632296, member: 593073"] Ok, no naked sister pic, but it does get a bit more attention for my post.. [COLOR=Blue][SIZE=12px]I have a Memphis Belle Amp[/SIZE][/COLOR][SIZE=12px][/SIZE] RMS Power 4 Ohm Stereo Ch 1-4/Ch 5 (4 ohm Mono) 14.4V….......75 watts x4/300 watts x1 RMS Power 2 Ohm Stereo Ch 1-4/Ch 5 (2 ohm Mono) 14.4V………..115 watts x4/600 watts x1 [COLOR=blue]RMS Power 4 Ohm Bridged Ch 1-4/Ch 5 (1 ohm Mono) 14.4V………230 watts x2/1100 watts x1 [/COLOR] Input Sensitivity……..250mV-9V Frequency Response +/- 1dB……..10Hz-50kHz/10Hz-650Hz Dimensions 7.6" x 2.4" x……….25.8125" Optional Remote Gain Control…….. MCRG [COLOR=blue][SIZE=12px]I want to run the amp this way[/SIZE][/COLOR][SIZE=12px][/SIZE][COLOR=blue]…[/COLOR] [COLOR=blue][SIZE=14px]RMS Power 4 Ohm Bridged Ch 1-4/Ch 5 (1 ohm Mono) 14.4V………230 watts x2/1100 watts x1[/SIZE][/COLOR][SIZE=14px][/SIZE] [COLOR=Red]It should be sufficient enough to run the 2 15" mojos and then 2x 12" M3's. the mojo's have an rms rating around 1,000wtts and the M3 is 400 rms. so if I push 230wtts to each M3 and about 550 watts to each mojo. This should be just fine enough…right?[/COLOR] This sounds great and all, but I’d rather just run 2 Mojos and use the other channels for my mids/highs… any advice on how to wire this.. [COLOR=blue]are there any component/mids/highs out there that can handle lots of power.. [/COLOR] [COLOR=blue][SIZE=12px]It seems like I can only run the amp as a 3channel or 5channel and I definetly want to run 2 Mojos at 550wtts each.. but the remaining 230wtts need to be for highs.. what do I do.. just turn the gain way down[/SIZE][/COLOR][SIZE=12px][/SIZE][COLOR=blue]?[/COLOR] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Memphis Mojo/HIGHS Wiring Help..
Top
Menu
Home
Refresh