Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
I went balls-deep in some CDT poon and this is what birthed itself...
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="marleyskater420" data-source="post: 7944867" data-attributes="member: 549075"><p>Yea the two panels were drying last night and hopefully finished drying today.</p><p></p><p>The thing with this stuff is that it really needs to be in the optimal temp to dry. With the home depot resin it was freezing out but it would still dry.</p><p></p><p>The nice thing though about it taking a long time to cure, is that if you need to cut more fabric or grab some food, you aren't pressed for time. I never mixed more than 4oz at a time and I have yet to waste any.</p><p></p><p>Depending on how ready they are tonight I'll try and take a few pics of the microspheres and show you how they mix in. The spheres are also good if you have really thin resin and you need something to "weigh" it up so it doesn't roll off the panel. Like on a vertical surface or something. I'll be using them when I make my big amp rack. I plan on doing 8 cdt es-06+'s in a V A (for vertex audio) configuration. 2 will be like this \ two like / then the amp in the center, then / and the last two \</p><p></p><p>So it'll look like \/ amp /\ however if I keep this xion (it does do 4x300 @1ohm and 2x605@2ohm bridged) I might need to figure a new way to do things. Maybe take out the rear seats?</p><p></p><p>I plan on having each 06+ in its own box (if possible) in .5cu tuned to roughly 28hz via CDT's recommendations. Should get crazy low for some little dudes.</p></blockquote><p></p>
[QUOTE="marleyskater420, post: 7944867, member: 549075"] Yea the two panels were drying last night and hopefully finished drying today. The thing with this stuff is that it really needs to be in the optimal temp to dry. With the home depot resin it was freezing out but it would still dry. The nice thing though about it taking a long time to cure, is that if you need to cut more fabric or grab some food, you aren't pressed for time. I never mixed more than 4oz at a time and I have yet to waste any. Depending on how ready they are tonight I'll try and take a few pics of the microspheres and show you how they mix in. The spheres are also good if you have really thin resin and you need something to "weigh" it up so it doesn't roll off the panel. Like on a vertical surface or something. I'll be using them when I make my big amp rack. I plan on doing 8 cdt es-06+'s in a V A (for vertex audio) configuration. 2 will be like this \ two like / then the amp in the center, then / and the last two \ So it'll look like \/ amp /\ however if I keep this xion (it does do 4x300 @1ohm and 2x605@2ohm bridged) I might need to figure a new way to do things. Maybe take out the rear seats? I plan on having each 06+ in its own box (if possible) in .5cu tuned to roughly 28hz via CDT's recommendations. Should get crazy low for some little dudes. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
I went balls-deep in some CDT poon and this is what birthed itself...
Top
Menu
Home
Refresh