Reply to thread

Message

<blockquote data-quote="2000LaDe" data-source="post: 6660472" data-attributes="member: 569818">so i have an RD 7500.1 that i have not used since i bought it off ss audio mike.&nbsp; i was planning on using it in my truck but since a deer blasted the side of my truck i need to get this gone.SPECS off thier siteThis is a Competition only amplifier and we do not recommend it for daily applications due to its massive power output and current draw.Recommended power supply– A minimum of six group 31 batteries and a high output alternator.The RD series amplifiers deliver a ton of power with a low distortion rate. We used the best parts we could find to give you a top quality amplifier that anyone would be proud to show off. With their clean looks and sleek finish, they’ll look good in any install. So whether it’s an elegant sound quality setup or a high powered SPL vehicle, the RD series amplifiers have you covered.Features* Digital class-D linkable mono block amplifier* MOSFET PWM power supply* Daisy-chain through output RCA* Heavy duty cooper layer double sided epoxy PCB* Stable into 1 ohm and 2 ohm parallel amplifier connection availability* 24 dB low pass (LPF) crossover variable* 18 dB bass boost equalization control variable* 180 degree variable adjustable phase shift* 24 dB subsonic filter variable* Selectable Switch for MASTER and SLAVE Operation* Speaker short, over current, thermal, and DC protection circuit* RCA line input and line output* 2 x 0 guage (AWG) battery input connectors* Efficiency: 86% at 4 ohm, 100 Hz* Tested voltage &amp;amp; THD : 14.4V and less than 1% THD at 4 ohm RMS watt* Operating voltage: DC 10V ~ 18V power input* Damping factor: better 350 into 1 ohm* Wired remote controllerMSRP$2899.00SpecificationsRMS power, .875 ohms mono&nbsp; &nbsp;&nbsp; 7500w X 1CHRMS power, 1 ohm mono&nbsp; &nbsp;&nbsp; 6000w X 1CHRMS power, 2 ohm mono&nbsp; &nbsp;&nbsp; 3000w X 1CHRMS power, 4 ohm mono&nbsp; &nbsp;&nbsp; 1500w X 1CHSignal to Noise Ratio&nbsp; &nbsp;&nbsp; &amp;gt;100dBLow pass frequency crossover&nbsp; &nbsp;&nbsp; 35Hz~300HzSubsonic filter&nbsp; &nbsp;&nbsp; 10Hz~60HzBass boost @ 45Hz&nbsp; &nbsp;&nbsp; 0~18dBPhase shift control&nbsp; &nbsp;&nbsp; 0~180 degreeFrequency response&nbsp; &nbsp;&nbsp; 10Hz~350Hz (+/- 1dB)T.H.D @ 4 ohmEfficiency @ 4 ohm&nbsp; &nbsp;&nbsp; 86%Fuse rating&nbsp; &nbsp;&nbsp; 600A(external type fuse - not included)Input Sensitivity&nbsp; &nbsp;&nbsp; 200mV to 6V (+/- 5%)Dimensions&nbsp; &nbsp;&nbsp; 222(W) x 52(H) x 870(L)mmpics -<img src="http://i10.photobucket.com/albums/a133/hankveach/106_0059.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" />this is the only problem i see with this case just a little ding on the corner<img src="http://i10.photobucket.com/albums/a133/hankveach/106_0060.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" />850+ ship</blockquote>

[QUOTE="2000LaDe, post: 6660472, member: 569818"] so i have an RD 7500.1 that i have not used since i bought it off ss audio mike. i was planning on using it in my truck but since a deer blasted the side of my truck i need to get this gone. [B][SIZE=24px]SPECS off thier site[/SIZE][/B] This is a Competition only amplifier and we do not recommend it for daily applications due to its massive power output and current draw. Recommended power supply– A minimum of six group 31 batteries and a high output alternator. The RD series amplifiers deliver a ton of power with a low distortion rate. We used the best parts we could find to give you a top quality amplifier that anyone would be proud to show off. With their clean looks and sleek finish, they’ll look good in any install. So whether it’s an elegant sound quality setup or a high powered SPL vehicle, the RD series amplifiers have you covered. Features * Digital class-D linkable mono block amplifier * MOSFET PWM power supply * Daisy-chain through output RCA * Heavy duty cooper layer double sided epoxy PCB * Stable into 1 ohm and 2 ohm parallel amplifier connection availability * 24 dB low pass (LPF) crossover variable * 18 dB bass boost equalization control variable * 180 degree variable adjustable phase shift * 24 dB subsonic filter variable * Selectable Switch for MASTER and SLAVE Operation * Speaker short, over current, thermal, and DC protection circuit * RCA line input and line output * 2 x 0 guage (AWG) battery input connectors * Efficiency: 86% at 4 ohm, 100 Hz * Tested voltage & THD : 14.4V and less than 1% THD at 4 ohm RMS watt * Operating voltage: DC 10V ~ 18V power input * Damping factor: better 350 into 1 ohm * Wired remote controller MSRP $2899.00 Specifications RMS power, .875 ohms mono 7500w X 1CH RMS power, 1 ohm mono 6000w X 1CH RMS power, 2 ohm mono 3000w X 1CH RMS power, 4 ohm mono 1500w X 1CH Signal to Noise Ratio >100dB Low pass frequency crossover 35Hz~300Hz Subsonic filter 10Hz~60Hz Bass boost @ 45Hz 0~18dB Phase shift control 0~180 degree Frequency response 10Hz~350Hz (+/- 1dB) T.H.D @ 4 ohm Efficiency @ 4 ohm 86% Fuse rating 600A(external type fuse - not included) Input Sensitivity 200mV to 6V (+/- 5%) Dimensions 222(W) x 52(H) x 870(L)mm pics - [IMG]http://i10.photobucket.com/albums/a133/hankveach/106_0059.jpg[/IMG] this is the only problem i see with this case just a little ding on the corner [IMG]http://i10.photobucket.com/albums/a133/hankveach/106_0060.jpg[/IMG] [B][SIZE=36px]850+ ship[/SIZE][/B] [/QUOTE]

Verification