Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Equipment choice/setup/wiring help
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Buldg7" data-source="post: 8571766" data-attributes="member: 672486"><p>Hey Guys, so I've got a bit of a dilemma on my hands. For my custom car audio install, which is almost entirely planned out already and I really don't want to change too much at this stage, I want to use the Alpine PXA-H800 DSP in its 5.1ch mode. The thing is that I want to drive it from a Pioneer DEH-80PRS in network mode (High, Mid, Low). My question is how could I configure the H800 to accept that form of input? Or would I have to run the 80PRS in standard (Front, Rear, Sub)? I guess what's confusing to me is how the input side of the H800 can be configured, either in a 3x 2ch input configuration, a 2 input (one 4ch, one 2ch) configuration, or in a 5.1ch input configuration (Front L&amp;R, Rear L&amp;R, Center, and Sub). The thing I don't understand is could I have it set up to output 5.1ch from a stereo or 4ch input? Or is there a way to configure it so that the three stereo inputs are assigned to different frequency ranges (like how network mode on the 80PRS outputs) but all be used simultaneously? Because the way I'm reading it is that it would be three independent stereo inputs, configured to be connected to three different sources. Is that wrong or no?</p></blockquote><p></p>
[QUOTE="Buldg7, post: 8571766, member: 672486"] Hey Guys, so I've got a bit of a dilemma on my hands. For my custom car audio install, which is almost entirely planned out already and I really don't want to change too much at this stage, I want to use the Alpine PXA-H800 DSP in its 5.1ch mode. The thing is that I want to drive it from a Pioneer DEH-80PRS in network mode (High, Mid, Low). My question is how could I configure the H800 to accept that form of input? Or would I have to run the 80PRS in standard (Front, Rear, Sub)? I guess what's confusing to me is how the input side of the H800 can be configured, either in a 3x 2ch input configuration, a 2 input (one 4ch, one 2ch) configuration, or in a 5.1ch input configuration (Front L&R, Rear L&R, Center, and Sub). The thing I don't understand is could I have it set up to output 5.1ch from a stereo or 4ch input? Or is there a way to configure it so that the three stereo inputs are assigned to different frequency ranges (like how network mode on the 80PRS outputs) but all be used simultaneously? Because the way I'm reading it is that it would be three independent stereo inputs, configured to be connected to three different sources. Is that wrong or no? [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Equipment choice/setup/wiring help
Top
Menu
Home
Refresh