Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Dsp settings. Amp gain
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Jimg" data-source="post: 8770920" data-attributes="member: 676695"><p>Using a Dayton dsp 408</p><p>What is the best way to go about this</p><p></p><p>should I turn my dsp gain about 3/4 of the way up on the output per channel and then adjust the amp gain to match the watts the speakers are rated for measuring voltage with different frequency based on the speaker hertz range going to the speakers </p><p></p><p>Or should I turn the dsp settings at about half voltage output. Turn the amp gain with an O scope to just under clipping </p><p>And then use the gain output on the dsp to adjust down if need be</p><p></p><p>trying to figure this dsp thing out. I am not getting anywhere near the volume in the car with the power I am running</p><p></p><p>my subs are plenty loud. I used a 40hz test tone to measure voltage going to the subs and have calculated that I am getting 1200 watts to the subs. Subs rated 600 watts rms each</p><p></p><p>just the tweeters and mids are not loud</p><p></p><p>I am running a 3 way active setup</p><p>Focal iss tweeter</p><p>Focal iss 5 1/4</p><p>Focal iss 6/12</p><p></p><p>how do you adjust dsp outputgain settings on the amplifierto get the most out up your system</p><p></p><p>I have already measured the output from the head unit and know the max volume setting that the Dayton dsp recommended on the input</p><p></p><p>amps used. Us acoustics mike 1500 watts</p><p>Barbara Ann 4x100. On the mids</p><p> Pioneer premier 2x35 watts on the tweeters </p><p></p><p>I feel I have enough watts just not getting the performance it should be.</p></blockquote><p></p>
[QUOTE="Jimg, post: 8770920, member: 676695"] Using a Dayton dsp 408 What is the best way to go about this should I turn my dsp gain about 3/4 of the way up on the output per channel and then adjust the amp gain to match the watts the speakers are rated for measuring voltage with different frequency based on the speaker hertz range going to the speakers Or should I turn the dsp settings at about half voltage output. Turn the amp gain with an O scope to just under clipping And then use the gain output on the dsp to adjust down if need be trying to figure this dsp thing out. I am not getting anywhere near the volume in the car with the power I am running my subs are plenty loud. I used a 40hz test tone to measure voltage going to the subs and have calculated that I am getting 1200 watts to the subs. Subs rated 600 watts rms each just the tweeters and mids are not loud I am running a 3 way active setup Focal iss tweeter Focal iss 5 1/4 Focal iss 6/12 how do you adjust dsp outputgain settings on the amplifierto get the most out up your system I have already measured the output from the head unit and know the max volume setting that the Dayton dsp recommended on the input amps used. Us acoustics mike 1500 watts Barbara Ann 4x100. On the mids Pioneer premier 2x35 watts on the tweeters I feel I have enough watts just not getting the performance it should be. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Dsp settings. Amp gain
Top
Menu
Home
Refresh