Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
custom crossover and maintaining ohm rating need help please.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="mpfjr" data-source="post: 7057789" data-attributes="member: 627102"><p>Ok so I decided to re-do my front componet set. I had a MB Quart refrence 6x9 componet set. It is powered straight from the head unit a Pioneer P4200-DVD.</p><p></p><p>The cut off for the tweeter is at 3800hz and the sytem seemed to have a hole at about 2000hz.</p><p></p><p>I ended up buying a pair of Tang 2" drivers that have a range form 160Hz to 20KHz and I put a non-polarity 100uf cap on the positive side right at the speaker and I hot glued the cap to the back of the magnet.</p><p></p><p>Wired up straight it works great but now I turn my attention to the 6x9 in the door. I understand that to do a low frequency filter you use a coil which is fine but where my question comes in is how do I maintain the 4ohm rating on each channel? There must be one item I need to introduce into the mix that allows me to bring the ohm load to 4.</p><p></p><p>this is my first time doing any of this so I would appreciate some help with which items I'd need to buy and how to wire them. I don't want to run an amp in this car.</p><p></p><p>Thanks</p><p></p><p>//content.invisioncic.com/y282845/emoticons/graduate.gif.d982460be9f153bb54e5d4cb744f6ae8.gif</p></blockquote><p></p>
[QUOTE="mpfjr, post: 7057789, member: 627102"] Ok so I decided to re-do my front componet set. I had a MB Quart refrence 6x9 componet set. It is powered straight from the head unit a Pioneer P4200-DVD. The cut off for the tweeter is at 3800hz and the sytem seemed to have a hole at about 2000hz. I ended up buying a pair of Tang 2" drivers that have a range form 160Hz to 20KHz and I put a non-polarity 100uf cap on the positive side right at the speaker and I hot glued the cap to the back of the magnet. Wired up straight it works great but now I turn my attention to the 6x9 in the door. I understand that to do a low frequency filter you use a coil which is fine but where my question comes in is how do I maintain the 4ohm rating on each channel? There must be one item I need to introduce into the mix that allows me to bring the ohm load to 4. this is my first time doing any of this so I would appreciate some help with which items I'd need to buy and how to wire them. I don't want to run an amp in this car. Thanks [IMG]//content.invisioncic.com/y282845/emoticons/graduate.gif.d982460be9f153bb54e5d4cb744f6ae8.gif[/IMG] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
custom crossover and maintaining ohm rating need help please.
Top
Menu
Home
Refresh