Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Correctly installing two drivers and an amp
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="x2o" data-source="post: 4955221" data-attributes="member: 582175"><p>Hey, welcome to the forums.</p><p></p><p>Well, after searching around I found that the MTX Thunder 3000's only come in single 4 and 8 ohm voice coils, so either way you are sending a safe load to the amp. (if single 4 you can wire down to 2 ohm, the JL slash series is good down to 1.5ohm)</p><p></p><p>Now, do you have a Digital MultiMeter (DMM) easily available? If so, I would check what the final ohm load is that your getting from your woofers.</p><p></p><p>This very well could be your amp getting hot, but that would be odd as I've heard the JL amps run very cool... Next time this happens, touch your amp's heatsink. Does it feel ridiculously hot?</p><p></p><p>Also, that JL amp is a good match for these two subs as they are rated at 200 RMS and the JL puts out 500. The sealed box is good for a basic setup, however a custom built ported box will get louder.</p><p></p><p>Any more questions just post up again in this thread! //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif</p></blockquote><p></p>
[QUOTE="x2o, post: 4955221, member: 582175"] Hey, welcome to the forums. Well, after searching around I found that the MTX Thunder 3000's only come in single 4 and 8 ohm voice coils, so either way you are sending a safe load to the amp. (if single 4 you can wire down to 2 ohm, the JL slash series is good down to 1.5ohm) Now, do you have a Digital MultiMeter (DMM) easily available? If so, I would check what the final ohm load is that your getting from your woofers. This very well could be your amp getting hot, but that would be odd as I've heard the JL amps run very cool... Next time this happens, touch your amp's heatsink. Does it feel ridiculously hot? Also, that JL amp is a good match for these two subs as they are rated at 200 RMS and the JL puts out 500. The sealed box is good for a basic setup, however a custom built ported box will get louder. Any more questions just post up again in this thread! [IMG]//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif[/IMG] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Correctly installing two drivers and an amp
Top
Menu
What's new
Forum list