Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
Clarion Full Digital - Crossover Help
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Jackers" data-source="post: 8585436" data-attributes="member: 673137"><p>Hi,</p><p></p><p>I am trying to setup the new Full Digital System from Clarion (Z3 tweeters, Z7 mids for front and rear doors, and dual Z25W subs.</p><p></p><p>This system is unique in that it processes the digital signal and sends it to the speakers in 1s and 0s. From there, the speaker processes that into cone movement. This eliminates the need for big amplifiers while eliminating electrical interference.</p><p></p><p>So, I'm trying to set my active crossovers for this, but because it is still so new, there isn't a lot of help online. Here is what I'm working with and what my original settings are. Any help would be greatly appreciated!</p><p></p><p>Z3 tweeters:</p><p></p><p>6ohm</p><p></p><p>1.5kHz ~ 40kHz</p><p></p><p>Z7 mids:</p><p></p><p>Driving section:</p><p></p><p>89dB at 1W S/N</p><p></p><p>102dB Dynamic Range</p><p></p><p>10Hz ~ 48kHz +/- 2dB Freq Response</p><p></p><p>Speaker section:</p><p></p><p>4ohm</p><p></p><p>28Hz ~ 15kHz</p><p></p><p>60Hz Fs</p><p></p><p>0.85 Qts</p><p></p><p>Z25W subs:</p><p></p><p>Driving section:</p><p></p><p>90dB at 1W S/N</p><p></p><p>103 dB Dynamic Range</p><p></p><p>10Hz ~ 48kHz +/- 2dB</p><p></p><p>Speaker section:</p><p></p><p>4ohm</p><p></p><p>20Hz ~ 200Hz Frequency Response</p><p></p><p>38Hz Fs</p><p></p><p>4.75 Qms</p><p></p><p>And this is what I have so far. Any advice on how to dial this in?</p><p></p><p>Tweeters:</p><p></p><p>HPF = 3.15kHz</p><p></p><p>Slope = -24</p><p></p><p>Gain =-9.0</p><p></p><p>Phase = Normal</p><p></p><p>Mids:</p><p></p><p>HPF = 80Hz</p><p></p><p>Slope = -24</p><p></p><p>LPF = 2.5kHz</p><p></p><p>Slope = -18</p><p></p><p>Gain = 0</p><p></p><p>Phase = REV</p><p></p><p>Subs:</p><p></p><p>HPF = 20Hz</p><p></p><p>Slope = -12</p><p></p><p>LPF = 80Hz</p><p></p><p>Slope = -12</p><p></p><p>Gain = 0</p><p></p><p>Phase = Normal</p></blockquote><p></p>
[QUOTE="Jackers, post: 8585436, member: 673137"] Hi, I am trying to setup the new Full Digital System from Clarion (Z3 tweeters, Z7 mids for front and rear doors, and dual Z25W subs. This system is unique in that it processes the digital signal and sends it to the speakers in 1s and 0s. From there, the speaker processes that into cone movement. This eliminates the need for big amplifiers while eliminating electrical interference. So, I'm trying to set my active crossovers for this, but because it is still so new, there isn't a lot of help online. Here is what I'm working with and what my original settings are. Any help would be greatly appreciated! Z3 tweeters: 6ohm 1.5kHz ~ 40kHz Z7 mids: Driving section: 89dB at 1W S/N 102dB Dynamic Range 10Hz ~ 48kHz +/- 2dB Freq Response Speaker section: 4ohm 28Hz ~ 15kHz 60Hz Fs 0.85 Qts Z25W subs: Driving section: 90dB at 1W S/N 103 dB Dynamic Range 10Hz ~ 48kHz +/- 2dB Speaker section: 4ohm 20Hz ~ 200Hz Frequency Response 38Hz Fs 4.75 Qms And this is what I have so far. Any advice on how to dial this in? Tweeters: HPF = 3.15kHz Slope = -24 Gain =-9.0 Phase = Normal Mids: HPF = 80Hz Slope = -24 LPF = 2.5kHz Slope = -18 Gain = 0 Phase = REV Subs: HPF = 20Hz Slope = -12 LPF = 80Hz Slope = -12 Gain = 0 Phase = Normal [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
Clarion Full Digital - Crossover Help
Top
Menu
Home
Refresh