Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Speakers
CDT Speakers distorting:(
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="jonB" data-source="post: 476224" data-attributes="member: 548994"><p>I am running an avionixx 440.4 amp to my cdt cl61a comps in my rsx-s. I have the gain set CLOSE to 0 on this amp otherwise these speakers begin to distort badly. The head unit is an alpine 9802 and has 3 sets of 4 volt preouts.</p><p></p><p>THe cdt xovers are set at 3db gain however at 0db there is still much distortion produced. I set my system by cranking the alpine head unit volume to max and moved the amps gain starting from 0 till the speakers began to distort then roll back slightly. Also while doing this the deck's settings are set to flat (example: bass and treble set to 0 and xover settings at 80 hz).</p><p></p><p>I tried messing with the cens settings on this amp to balance in the rca input signal but the difference is minimal.</p><p></p><p>Anyone else using these speakers and experiencing the same thing ( having to run gain very low)? The speakers are rated to something like 80wrms and I suspect I am not running hear that at the current gain level. Once i go past say volume 25 on the deck, the speakers begin to breakup slightly and the treble from the tweeters goes flat (protection circuitry is kicking in).</p><p></p><p>Is this the workings of a shitty signal coming from my amp or do these speakers really operate cleanly only at very low gain?</p></blockquote><p></p>
[QUOTE="jonB, post: 476224, member: 548994"] I am running an avionixx 440.4 amp to my cdt cl61a comps in my rsx-s. I have the gain set CLOSE to 0 on this amp otherwise these speakers begin to distort badly. The head unit is an alpine 9802 and has 3 sets of 4 volt preouts. THe cdt xovers are set at 3db gain however at 0db there is still much distortion produced. I set my system by cranking the alpine head unit volume to max and moved the amps gain starting from 0 till the speakers began to distort then roll back slightly. Also while doing this the deck's settings are set to flat (example: bass and treble set to 0 and xover settings at 80 hz). I tried messing with the cens settings on this amp to balance in the rca input signal but the difference is minimal. Anyone else using these speakers and experiencing the same thing ( having to run gain very low)? The speakers are rated to something like 80wrms and I suspect I am not running hear that at the current gain level. Once i go past say volume 25 on the deck, the speakers begin to breakup slightly and the treble from the tweeters goes flat (protection circuitry is kicking in). Is this the workings of a shitty signal coming from my amp or do these speakers really operate cleanly only at very low gain? [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Speakers
CDT Speakers distorting:(
Top
Menu
Home
Refresh