Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Car electrical system going haywire after head unit install
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="gleep52" data-source="post: 7702755" data-attributes="member: 640862"><p>I'm no expert, but my thoughts are - your system has a system that is controlled via computer. In my 06 Chrysler, there is one wire on my factory harness that is for the can bus system - that line is for digital signals, not a 12 volt on or off wire. It is orange, which I almost hooked it up to the dimmer wire for my head unit. Thankfully my radio actually had the pin-outs labeled right on the deck, so I knew not to hook up that wire or I would have fried my control module.</p><p></p><p>I think you might have done some serious damage - but I could be totally wrong and it might be nothing like what I'm talking about... If you disconnect your new head-unit completely and put the stock one in, and the problem goes away - then at least you haven't done permanent damage. If the problem goes away with the factory head unit installed, chances are either something is wrong in your wiring or perhaps something is wrong with your head unit.</p><p></p><p>If the problem doesn't go away with the factory head unit - chances are - you've got a bigger problem than you want.</p><p></p><p>Fingers are crossed for you buddy - hope someone has better news for you than I do.</p></blockquote><p></p>
[QUOTE="gleep52, post: 7702755, member: 640862"] I'm no expert, but my thoughts are - your system has a system that is controlled via computer. In my 06 Chrysler, there is one wire on my factory harness that is for the can bus system - that line is for digital signals, not a 12 volt on or off wire. It is orange, which I almost hooked it up to the dimmer wire for my head unit. Thankfully my radio actually had the pin-outs labeled right on the deck, so I knew not to hook up that wire or I would have fried my control module. I think you might have done some serious damage - but I could be totally wrong and it might be nothing like what I'm talking about... If you disconnect your new head-unit completely and put the stock one in, and the problem goes away - then at least you haven't done permanent damage. If the problem goes away with the factory head unit installed, chances are either something is wrong in your wiring or perhaps something is wrong with your head unit. If the problem doesn't go away with the factory head unit - chances are - you've got a bigger problem than you want. Fingers are crossed for you buddy - hope someone has better news for you than I do. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Car electrical system going haywire after head unit install
Top
Menu
What's new
Forum list