Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
Box Build Help
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="c9obr6a" data-source="post: 8816959" data-attributes="member: 687071"><p>Hello all, making a box for my daughter and haven’t done anything like this since the 90’s. I’ve been reading / researching allot and think I have a decent design attached below for a single Fosgate 10” P3. Was hoping for feedback or if anyone can check the performance of the box on a builder program. Definitely appreciate any help, hate to waist a bunch of time and $$. I did reach out to the Manufacture and they recommended 40Hz tuning and not to go lower. Outside of Box would be 20 ½” x 14”x14” out of .75” MDF screwed and glued.</p><p></p><p>Vehicle : 2016 Fusion</p><p></p><p>Location in the vehicle: trunk</p><p></p><p>Space available (Length x Width x Height): 40x14x14</p><p></p><p>Subwoofer make and model: Fosgate P3 10” DVC 2 Ohm</p><p></p><p>Subwoofer Size: 10”</p><p></p><p>Number of Subwoofers: 1</p><p></p><p>Type of Port (Kerfed, Slot, Aero, etc.): Slot Front</p><p></p><p>What type of music do you like?: All, Teenage Girl</p><p></p><p>Is your goal SPL or Everyday Music?: everyday Music</p><p></p><p>Tuning Freq (Hz): 40</p><p></p><p>Volume : 1.40</p><p></p><p>Questions: below sketch -up drawing going to work?</p></blockquote><p></p>
[QUOTE="c9obr6a, post: 8816959, member: 687071"] Hello all, making a box for my daughter and haven’t done anything like this since the 90’s. I’ve been reading / researching allot and think I have a decent design attached below for a single Fosgate 10” P3. Was hoping for feedback or if anyone can check the performance of the box on a builder program. Definitely appreciate any help, hate to waist a bunch of time and $$. I did reach out to the Manufacture and they recommended 40Hz tuning and not to go lower. Outside of Box would be 20 ½” x 14”x14” out of .75” MDF screwed and glued. Vehicle : 2016 Fusion Location in the vehicle: trunk Space available (Length x Width x Height): 40x14x14 Subwoofer make and model: Fosgate P3 10” DVC 2 Ohm Subwoofer Size: 10” Number of Subwoofers: 1 Type of Port (Kerfed, Slot, Aero, etc.): Slot Front What type of music do you like?: All, Teenage Girl Is your goal SPL or Everyday Music?: everyday Music Tuning Freq (Hz): 40 Volume : 1.40 Questions: below sketch -up drawing going to work? [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
Box Build Help
Top
Menu
Home
Refresh