Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
Head Units
audiocontrol three.1 crossover question
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="vaiboy" data-source="post: 8308483" data-attributes="member: 570683"><p>AudioControl uses 16pin 8 resistor Bourns resistor networks to set the crossover frequency of their 24dB crossovers. The first thing you need to do is determine the resistance for your desired crossover frequency. The formula for that is 7200÷F=R, where F is your desired frequency and R is the resistance in kΩ. The Three.1 comes from the factory set at 90hz, I wouldn't lower it too much though, when you change it you are also lowering the low pass filter on the sub channel. Here's a link to the crossover networks on DigiKey if they don't stock the one you need you can "build" your own using 8 individual resistors, or you can buy them through AudioControl but that's the expensive option.</p><p></p><p><a href="http://www.digikey.com/product-search/en?v=118&amp;s=18544&amp;pv9=2&amp;pv238=7&amp;pv10=5&amp;FV=fff40001%2Cfff80007&amp;mnonly=0&amp;newproducts=0&amp;ColumnSort=0&amp;page=1&amp;quantity=0&amp;ptm=0&amp;fid=0&amp;pageSize=25" target="_blank">DigiKey</a></p></blockquote><p></p>
[QUOTE="vaiboy, post: 8308483, member: 570683"] AudioControl uses 16pin 8 resistor Bourns resistor networks to set the crossover frequency of their 24dB crossovers. The first thing you need to do is determine the resistance for your desired crossover frequency. The formula for that is 7200÷F=R, where F is your desired frequency and R is the resistance in kΩ. The Three.1 comes from the factory set at 90hz, I wouldn't lower it too much though, when you change it you are also lowering the low pass filter on the sub channel. Here's a link to the crossover networks on DigiKey if they don't stock the one you need you can "build" your own using 8 individual resistors, or you can buy them through AudioControl but that's the expensive option. [URL="http://www.digikey.com/product-search/en?v=118&s=18544&pv9=2&pv238=7&pv10=5&FV=fff40001%2Cfff80007&mnonly=0&newproducts=0&ColumnSort=0&page=1&quantity=0&ptm=0&fid=0&pageSize=25"]DigiKey[/URL] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Head Units
audiocontrol three.1 crossover question
Top
Menu
What's new
Forum list