Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
any bored designers?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="k_schutte" data-source="post: 8088939" data-attributes="member: 551817"><p>Hey guys... So, my computer is in the shop, will be for a little while so I don't have access to any of my programs. I was wondering if any of you box designers were bored and might wanna slap something together for me? I'm throwing my Orphan 8" in my boat, in a 4th order.</p><p></p><p>here are the max dimensions:</p><p></p><p>height: 17"</p><p></p><p>width: 18"</p><p></p><p>depth: 26"</p><p></p><p>I was planning to have the sealed chamber in top, ported on bottom. Sub occupying the sealed chamber obviously and firing down into the ported chamber. Port on the bottom, firing toward the rear of the boat. (so port would need to be in the "width" area). I was planning .3/.6 with the ported side tuned to 50hz~ but I am not a bandpass expert by ANY stretch of the imagination so...</p><p></p><p>Qts - 0.405</p><p></p><p>Qes - 0.442</p><p></p><p>Qms - 4.778</p><p></p><p>Fs - 34.289 Hz</p><p></p><p>Re - 5.25 Ohm</p><p></p><p>Ls - 12.16mH</p><p></p><p>Lp - 4.053 mH</p><p></p><p>Rp - 25.46 Ohm</p><p></p><p>Vas - 5.031 L</p><p></p><p>Mms - 214.1 g</p><p></p><p>Cms - 100.6 m/N</p><p></p><p>Bl - 23.39 T*m</p><p></p><p>Sensitivity - 78.44 dB</p><p></p><p>17mm Xmax</p></blockquote><p></p>
[QUOTE="k_schutte, post: 8088939, member: 551817"] Hey guys... So, my computer is in the shop, will be for a little while so I don't have access to any of my programs. I was wondering if any of you box designers were bored and might wanna slap something together for me? I'm throwing my Orphan 8" in my boat, in a 4th order. here are the max dimensions: height: 17" width: 18" depth: 26" I was planning to have the sealed chamber in top, ported on bottom. Sub occupying the sealed chamber obviously and firing down into the ported chamber. Port on the bottom, firing toward the rear of the boat. (so port would need to be in the "width" area). I was planning .3/.6 with the ported side tuned to 50hz~ but I am not a bandpass expert by ANY stretch of the imagination so... Qts - 0.405 Qes - 0.442 Qms - 4.778 Fs - 34.289 Hz Re - 5.25 Ohm Ls - 12.16mH Lp - 4.053 mH Rp - 25.46 Ohm Vas - 5.031 L Mms - 214.1 g Cms - 100.6 m/N Bl - 23.39 T*m Sensitivity - 78.44 dB 17mm Xmax [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
any bored designers?
Top
Menu
What's new
Forum list