Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
Amps turning off
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="West1" data-source="post: 8560557" data-attributes="member: 586208"><p>Battery is 3 months old at tops. Alt is stock 2007 atl and will be replacing hopefully with in a week or 2.</p><p></p><p>Big three got delayed because the frontier has a 1/2 inch diameter sensor I can't pass between batt neg and engine block. I tried to slither a 0 gauge but after an hour my fingers and brain gave up lol. Ordered 1 gauge (not 1/0 gauge) to fill that and it's in my possession. Just no extra time.</p><p></p><p>I'll try and finish big 3 this weekend.</p><p></p><p>Positive on low and highs looked good. As I said, I'll double check tomorrow.</p><p></p><p>The one thing you mention was the fuse holders. One does have a burned mark on it. I purchased a roll of 0 gauge and plan to replace the 2 gauge wire to amps with the 0 gauge. Again, time has not been friendly. Im using 100amp fuse per amp at the battery as the fuses on the amp are just under 100amps. I also purchased new fuse holders and will swap the cylinder 100 fuses for the anl fuses.</p><p></p><p>Also, not sure if the remote wires on the amp meet up, I'll have to pay attention when I have a look tomorrow.</p><p></p><p>Tyvm for the help guys, I appreciate it. It's also doing my brain in lol</p></blockquote><p></p>
[QUOTE="West1, post: 8560557, member: 586208"] Battery is 3 months old at tops. Alt is stock 2007 atl and will be replacing hopefully with in a week or 2. Big three got delayed because the frontier has a 1/2 inch diameter sensor I can't pass between batt neg and engine block. I tried to slither a 0 gauge but after an hour my fingers and brain gave up lol. Ordered 1 gauge (not 1/0 gauge) to fill that and it's in my possession. Just no extra time. I'll try and finish big 3 this weekend. Positive on low and highs looked good. As I said, I'll double check tomorrow. The one thing you mention was the fuse holders. One does have a burned mark on it. I purchased a roll of 0 gauge and plan to replace the 2 gauge wire to amps with the 0 gauge. Again, time has not been friendly. Im using 100amp fuse per amp at the battery as the fuses on the amp are just under 100amps. I also purchased new fuse holders and will swap the cylinder 100 fuses for the anl fuses. Also, not sure if the remote wires on the amp meet up, I'll have to pay attention when I have a look tomorrow. Tyvm for the help guys, I appreciate it. It's also doing my brain in lol [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
Amps turning off
Top
Menu
Home
Refresh