Reply to thread

Message

<blockquote data-quote="joeb1983" data-source="post: 7068672" data-attributes="member: 627283">I have a visonik V8212 AMP the spects are as follows i am running 2 &quot;10&quot; sub SONY XPLODS XS-L1000B Max peak is 650W i have briged the subs as well they sound good but i&nbsp; changed so of the wireing and first i blew the inline fuse next to the battery&nbsp; i thought it might of been from reconnecting it while the battery was connected&nbsp; but i did not blow then it was later&nbsp; when i was driving when i raised the volume i could not idenify the Amp on originall fuse so i put a 40A in the problem im having is during volume increase it shuts off and flickers like it can&#039;t turn on i don&#039;t know what i did wrong i just replace speaker wire and bridged the unit here are my specesNumber of Channels 2RMS Power (4 ohms) N/ARMS Power (2 ohms) N/ARMS Power (1 ohm) N/ABridged RMS Power N/ATotal RMS Power Output 400 wattsPeak Power Output 800 watts x 1 channelTotal Peak Power Output 800 wattsMinimum Impedance Unbridged N/AMinimum Impedance Bridged N/ATHD at Rated RMS Power N/ASpeaker Level Inputs N/APreamp Outputs 1 pairBuilt-in Crossover Low-pass (LP)High-pass (HP)High-Pass Crossover Frequency N/ALow-Pass Crossover Frequency N/ASubsonic Filter N/ASignal-to-Noise Ratio N/AChannel Separation N/ABass Boost 0 - 18 dBBass/Gain Remote NoFan Cooled NoFuse RatingMy power wire is a 6 gage amp wire from battery to amp with 40 Amp fuse im using a 8&nbsp; gage for ground and 14 gage remote wire with 18 gage speaker wireWhat is proper wire gage i should use if wrong and size fuse</blockquote>

[QUOTE="joeb1983, post: 7068672, member: 627283"] I have a visonik V8212 AMP the spects are as follows i am running 2 "10" sub SONY XPLODS XS-L1000B Max peak is 650W i have briged the subs as well they sound good but i changed so of the wireing and first i blew the inline fuse next to the battery i thought it might of been from reconnecting it while the battery was connected but i did not blow then it was later when i was driving when i raised the volume i could not idenify the Amp on originall fuse so i put a 40A in the problem im having is during volume increase it shuts off and flickers like it can't turn on i don't know what i did wrong i just replace speaker wire and bridged the unit here are my speces Number of Channels 2 RMS Power (4 ohms) N/A RMS Power (2 ohms) N/A RMS Power (1 ohm) N/A Bridged RMS Power N/A Total RMS Power Output 400 watts Peak Power Output 800 watts x 1 channel Total Peak Power Output 800 watts Minimum Impedance Unbridged N/A Minimum Impedance Bridged N/A THD at Rated RMS Power N/A Speaker Level Inputs N/A Preamp Outputs 1 pair Built-in Crossover Low-pass (LP) High-pass (HP) High-Pass Crossover Frequency N/A Low-Pass Crossover Frequency N/A Subsonic Filter N/A Signal-to-Noise Ratio N/A Channel Separation N/A Bass Boost 0 - 18 dB Bass/Gain Remote No Fan Cooled No Fuse Rating My power wire is a 6 gage amp wire from battery to amp with 40 Amp fuse im using a 8 gage for ground and 14 gage remote wire with 18 gage speaker wire What is proper wire gage i should use if wrong and size fuse [/QUOTE]

Verification