Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
Amplifiers
Amp problem... phoenix gold mps2500???
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="lastcall" data-source="post: 1321043" data-attributes="member: 564672"><p>This amp was recently just givin to me... i dont know too much about it except it was hardly used,its an older amp, and it pushed 2 jl audio15w4's when they cam out. i think this amp was released in 1994 or somewhere. my question....is this a good amp to power 2 JL Audio 10w3v1-d2s? if not let me know why or what to use.</p><p></p><p>Into 4 ohms @ 12.5/14.4 VDC</p><p></p><p>50/80 WRMS x 2</p><p></p><p>Into 2 ohms @ 14.4 VDC</p><p></p><p>125 WRMS x 2</p><p></p><p>Bridged into 2 ohm @ 14.4 VDC</p><p></p><p>510 WRMS x 1</p><p></p><p>Frequency Response</p><p></p><p>+/-1dB from 20Hz to 20kHz</p><p></p><p>Signal to Noise Ratio</p><p></p><p>&gt;100dB</p><p></p><p>Input Sensitivity</p><p></p><p>200 millivolts to 2 volts</p><p></p><p>Input Impedance</p><p></p><p>&gt;30k ohms</p><p></p><p>Input Voltage Range</p><p></p><p>10.5 volts to 15.0 volts</p><p></p><p>Typical current draw at idle</p><p></p><p>3 amps</p><p></p><p>Minimum Impedance MS series</p><p></p><p>2 ohm bridged/1ohm stereo</p><p></p><p>Minimum Impedance MPS series</p><p></p><p>1 ohm bridged/ .5 ohm stereo</p><p></p><p>Dimensions, MS250, MS275, MPS 2220, MPS2240</p><p></p><p>8.5"L x 11.4"W x 2.4"H</p><p></p><p>Dimensions, MS2125, MPS2500</p><p></p><p>17.0"L x 11.4 "W x 2.4"H</p><p></p><p>Dimensions, MS2250</p><p></p><p>25.5"L x 11.75"W x 3.35"H</p><p></p><p>Dimensions, MQ430</p><p></p><p>11.4"L x 11.0"W x 2.4"H</p></blockquote><p></p>
[QUOTE="lastcall, post: 1321043, member: 564672"] This amp was recently just givin to me... i dont know too much about it except it was hardly used,its an older amp, and it pushed 2 jl audio15w4's when they cam out. i think this amp was released in 1994 or somewhere. my question....is this a good amp to power 2 JL Audio 10w3v1-d2s? if not let me know why or what to use. Into 4 ohms @ 12.5/14.4 VDC 50/80 WRMS x 2 Into 2 ohms @ 14.4 VDC 125 WRMS x 2 Bridged into 2 ohm @ 14.4 VDC 510 WRMS x 1 Frequency Response +/-1dB from 20Hz to 20kHz Signal to Noise Ratio >100dB Input Sensitivity 200 millivolts to 2 volts Input Impedance >30k ohms Input Voltage Range 10.5 volts to 15.0 volts Typical current draw at idle 3 amps Minimum Impedance MS series 2 ohm bridged/1ohm stereo Minimum Impedance MPS series 1 ohm bridged/ .5 ohm stereo Dimensions, MS250, MS275, MPS 2220, MPS2240 8.5"L x 11.4"W x 2.4"H Dimensions, MS2125, MPS2500 17.0"L x 11.4 "W x 2.4"H Dimensions, MS2250 25.5"L x 11.75"W x 3.35"H Dimensions, MQ430 11.4"L x 11.0"W x 2.4"H [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Amplifiers
Amp problem... phoenix gold mps2500???
Top
Menu
What's new
Forum list
