Reply to thread

Message

<blockquote data-quote="SoggyFries" data-source="post: 8877099" data-attributes="member: 670482">Seems to work great. Thanks! Here a transcript.Me:&nbsp;&nbsp; I need plans for a single vented 10&quot; enclosure that is tuned to 32hz. One Sundown Audio E10 v3 d4 ohm is the sub that will be used. Please give specs as well as a cutout list and the plywood size board needed to make all the cuts.ChatGPT:For a single vented 10&quot; enclosure tuned to 32Hz for a Sundown Audio E10 v3 D4 subwoofer, here are the detailed plans, specs, cutout list, and material requirements.### Enclosure Specifications:- **Subwoofer Model**: Sundown Audio E10 v3 D4- **Type**: Vented (Ported)- **Tuning Frequency**: 32 Hz- **Internal Volume**: 1.25 cubic feet (after displacement of subwoofer and port)### Dimensions:- **External Dimensions**:&nbsp; - Width: 15 inches&nbsp; - Height: 15 inches&nbsp; - Depth: 14.5 inches- **Internal Dimensions**:&nbsp; - Width: 13.5 inches&nbsp; - Height: 13.5 inches&nbsp; - Depth: 13 inches### Port Specifications:- **Type**: Slot port- **Port Dimensions**:&nbsp; - Width: 1.5 inches&nbsp; - Height: 13.5 inches&nbsp; - Length: 25 inches (includes the bend)### Cut List:1. **Front &amp; Back Panels**: 15&quot; x 15&quot; (2 pieces)2. **Top &amp; Bottom Panels**: 15&quot; x 14.5&quot; (2 pieces)3. **Side Panels**: 13.5&quot; x 14.5&quot; (2 pieces)4. **Port Panels**:&nbsp;&nbsp; - First segment: 1.5&quot; x 13.5&quot; (1 piece)&nbsp;&nbsp; - Second segment: 1.5&quot; x 11.75&quot; (1 piece)&nbsp;&nbsp; - Third segment: 1.5&quot; x 7.75&quot; (1 piece)### Material Requirements:- **Material**: 3/4&quot; MDF or Plywood- **Board Size**: 4&#039; x 8&#039; sheet### Construction Tips:1. **Cut the MDF or plywood as per the dimensions listed in the cut list.**2. **Assemble the box by attaching the front, back, top, bottom, and side panels using wood glue and screws.**3. **Ensure all joints are sealed properly to avoid air leaks.**4. **Assemble the port inside the enclosure using the port panels.**5. **Cut out the subwoofer hole on the front panel according to the subwoofer&#039;s cutout diameter (9.25 inches).**6. **Mount the subwoofer in the cutout hole and secure it with screws.**7. **Optionally, add internal bracing for additional support and to minimize vibrations.**8. **Finish the enclosure with carpet, paint, or vinyl as desired.**### Cut Sheet Diagram:- **Front &amp; Back Panels**:&nbsp; ```&nbsp; ___________________&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |&nbsp; &nbsp; 15&quot; x 15&quot;&nbsp; &nbsp; |&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |_________________|&nbsp; ```- **Top &amp; Bottom Panels**:&nbsp; ```&nbsp; ___________________&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |&nbsp; 15&quot; x 14.5&quot;&nbsp; &nbsp; |&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |_________________|&nbsp; ```- **Side Panels**:&nbsp; ```&nbsp; _______________&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; | 13.5&quot; x 14.5&quot;|&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; |&nbsp; |_____________|&nbsp; ```- **Port Panels**:&nbsp; ```&nbsp; ______________________&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; |&nbsp; | 1.5&quot; x 13.5&quot; (1 pc) |&nbsp; |____________________|&nbsp; ______________________&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; |&nbsp; | 1.5&quot; x 11.75&quot; (1 pc)|&nbsp; |____________________|&nbsp; ______________________&nbsp; |&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; |&nbsp; | 1.5&quot; x 7.75&quot; (1 pc) |&nbsp; |____________________|&nbsp; ```### Assembly Diagram:![Assembly Diagram](https://www.diyaudio.com/forums/attachments/assembly_diagram-jpg.777187/)By following these specifications and instructions, you can build a high-quality enclosure optimized for your Sundown Audio E10 v3 D4 subwoofer tuned to 32Hz. This design will provide deep and powerful bass performance for your audio system.</blockquote>

[QUOTE="SoggyFries, post: 8877099, member: 670482"] Seems to work great. Thanks! Here a transcript. [U][B]Me:[/B][/U] I need plans for a single vented 10" enclosure that is tuned to 32hz. One Sundown Audio E10 v3 d4 ohm is the sub that will be used. Please give specs as well as a cutout list and the plywood size board needed to make all the cuts. [U][B]ChatGPT:[/B][/U] For a single vented 10" enclosure tuned to 32Hz for a Sundown Audio E10 v3 D4 subwoofer, here are the detailed plans, specs, cutout list, and material requirements. ### Enclosure Specifications: - **Subwoofer Model**: Sundown Audio E10 v3 D4 - **Type**: Vented (Ported) - **Tuning Frequency**: 32 Hz - **Internal Volume**: 1.25 cubic feet (after displacement of subwoofer and port) ### Dimensions: - **External Dimensions**: - Width: 15 inches - Height: 15 inches - Depth: 14.5 inches - **Internal Dimensions**: - Width: 13.5 inches - Height: 13.5 inches - Depth: 13 inches ### Port Specifications: - **Type**: Slot port - **Port Dimensions**: - Width: 1.5 inches - Height: 13.5 inches - Length: 25 inches (includes the bend) ### Cut List: 1. **Front & Back Panels**: 15" x 15" (2 pieces) 2. **Top & Bottom Panels**: 15" x 14.5" (2 pieces) 3. **Side Panels**: 13.5" x 14.5" (2 pieces) 4. **Port Panels**: - First segment: 1.5" x 13.5" (1 piece) - Second segment: 1.5" x 11.75" (1 piece) - Third segment: 1.5" x 7.75" (1 piece) ### Material Requirements: - **Material**: 3/4" MDF or Plywood - **Board Size**: 4' x 8' sheet ### Construction Tips: 1. **Cut the MDF or plywood as per the dimensions listed in the cut list.** 2. **Assemble the box by attaching the front, back, top, bottom, and side panels using wood glue and screws.** 3. **Ensure all joints are sealed properly to avoid air leaks.** 4. **Assemble the port inside the enclosure using the port panels.** 5. **Cut out the subwoofer hole on the front panel according to the subwoofer's cutout diameter (9.25 inches).** 6. **Mount the subwoofer in the cutout hole and secure it with screws.** 7. **Optionally, add internal bracing for additional support and to minimize vibrations.** 8. **Finish the enclosure with carpet, paint, or vinyl as desired.** ### Cut Sheet Diagram: - **Front & Back Panels**: ``` ___________________ | | | | | 15" x 15" | | | | | |_________________| ``` - **Top & Bottom Panels**: ``` ___________________ | | | | | 15" x 14.5" | | | | | |_________________| ``` - **Side Panels**: ``` _______________ | | | | | 13.5" x 14.5"| | | | | |_____________| ``` - **Port Panels**: ``` ______________________ | | | 1.5" x 13.5" (1 pc) | |____________________| ______________________ | | | 1.5" x 11.75" (1 pc)| |____________________| ______________________ | | | 1.5" x 7.75" (1 pc) | |____________________| ``` ### Assembly Diagram: ![Assembly Diagram](https://www.diyaudio.com/forums/attachments/assembly_diagram-jpg.777187/) By following these specifications and instructions, you can build a high-quality enclosure optimized for your Sundown Audio E10 v3 D4 subwoofer tuned to 32Hz. This design will provide deep and powerful bass performance for your audio system. [/QUOTE]

Verification