Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
400x4 amp with 6x9s wire up?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="RockyBalboa" data-source="post: 8689428" data-attributes="member: 678335"><p>Can you folks look at this and tell me if this is the most efficient hook up I can achieve , with out overheating, or blowing up the speakers? I only have the two rear 6x9s hooked up the Taramps 400x4. The front dash speakers are not wired to amp . If I bridge the 6x9s will it be to much for them ?</p><p></p><p>The 6x9s are Alpine s-s69, Handles up to 85 watts RMS (260 watts peak power), Frequency response: 65-22,000 Hz, Sensitivity: 90 dB. The speakers are 4 ohm speakers</p><p></p><p>The amp specs are </p><p>Technical Specs:Number of Channels: 04</p><ul> <li data-xf-list-type="ul">Maximum Power:</li> <li data-xf-list-type="ul">@ 13.8 VDC - 2 OHMS - 400 W RMS (4 x 100W RMS)</li> <li data-xf-list-type="ul">@ 13.8 VDC-4 OHMS - 252 W RMS (4 x 63W RMS)</li> <li data-xf-list-type="ul">Bridged @ 13.8 VDC - 4 OHMS - 400W RMS (2 x 200W RMS)</li> <li data-xf-list-type="ul">Input Sensitivity: 200mV (Vol=Max)</li> <li data-xf-list-type="ul">Signal to Noise Ratio: > 90dB</li> <li data-xf-list-type="ul">Frequency Response: (Full Range): 18Hz to 30kHz (-1dB)</li> <li data-xf-list-type="ul">High Pass Crossover (HPF): 90Hz (-12dB / 8th)</li> <li data-xf-list-type="ul">Low Pass Crossover (LPF): 90Hz (-12dB / 8th)</li> <li data-xf-list-type="ul">Input Impedance: 22K OHMS</li> <li data-xf-list-type="ul">Thermal Protection System and Short Output</li> <li data-xf-list-type="ul">Minimum Supply Voltage: 8 VDC</li> <li data-xf-list-type="ul">Maximum Supply Voltage: 16 VDC</li> <li data-xf-list-type="ul">Standby Power: 0.8 Amp.</li> <li data-xf-list-type="ul">Maximum Musical Power: @ 13.8VDC: 16.5 Amp.</li> <li data-xf-list-type="ul">Maximum Consumption in Sine Signal: (1kHz) 13.8VDC: 33 Amp.</li> <li data-xf-list-type="ul">Dimensions (WxDxH): 138 x 49 x 121mm</li> </ul><p></p><p>I have the 6x9s hooked up to channel one and two.</p></blockquote><p></p>
[QUOTE="RockyBalboa, post: 8689428, member: 678335"] Can you folks look at this and tell me if this is the most efficient hook up I can achieve , with out overheating, or blowing up the speakers? I only have the two rear 6x9s hooked up the Taramps 400x4. The front dash speakers are not wired to amp . If I bridge the 6x9s will it be to much for them ? The 6x9s are Alpine s-s69, Handles up to 85 watts RMS (260 watts peak power), Frequency response: 65-22,000 Hz, Sensitivity: 90 dB. The speakers are 4 ohm speakers The amp specs are Technical Specs:Number of Channels: 04 [LIST] [*]Maximum Power: [*]@ 13.8 VDC - 2 OHMS - 400 W RMS (4 x 100W RMS) [*]@ 13.8 VDC-4 OHMS - 252 W RMS (4 x 63W RMS) [*]Bridged @ 13.8 VDC - 4 OHMS - 400W RMS (2 x 200W RMS) [*]Input Sensitivity: 200mV (Vol=Max) [*]Signal to Noise Ratio: > 90dB [*]Frequency Response: (Full Range): 18Hz to 30kHz (-1dB) [*]High Pass Crossover (HPF): 90Hz (-12dB / 8th) [*]Low Pass Crossover (LPF): 90Hz (-12dB / 8th) [*]Input Impedance: 22K OHMS [*]Thermal Protection System and Short Output [*]Minimum Supply Voltage: 8 VDC [*]Maximum Supply Voltage: 16 VDC [*]Standby Power: 0.8 Amp. [*]Maximum Musical Power: @ 13.8VDC: 16.5 Amp. [*]Maximum Consumption in Sine Signal: (1kHz) 13.8VDC: 33 Amp. [*]Dimensions (WxDxH): 138 x 49 x 121mm [/LIST] I have the 6x9s hooked up to channel one and two. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
400x4 amp with 6x9s wire up?
Top
Menu
Home
Refresh