Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
2000 mercury mystique-first ever custom install and need advice
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="chefzane" data-source="post: 8105056" data-attributes="member: 654412"><p>A. Yes own sealed box</p><p></p><p>B. No not using the single</p><p></p><p>C. Yes its sealed</p><p></p><p>1. Yes I plan on fusing both ends in between battery's and fusing each 4 or 8 gauge run in between distro and amp, should I fuse the neg in between battery's and in between distro and amp also?</p><p></p><p>2. What should I use instead of y cables to go from two sets to four sets? Or just from one set to two cuz the xover only has three outs so I can just split one of those? I don't like y cables cuz ur basically splitting the voltage too right?</p><p></p><p>3. 6x9s and a set of tweets or two more component sets just diff size from what I already have. I can put them a couple places like in the kicks or in the doors if two more comp sets or move the eights to under front seats and put those in the rear deck box or eights to kicks but that's a ***** or in the front dash I dunno</p><p></p><p>4. What order does it go I know CLD on inside door skin, seal the door, then CCF, then MLV, then door panel?</p><p></p><p>5. What if I cut the back out of the box, turn the subs, then use the trunk area as the sealed portion or infinite baffle type setup? I don't have enough clearance to mount them between the seat and face of box, unless I cut it out and try to move it in making a small box smaller? What about a large slot behind 8" panel? Or move the eights, cut holes in that box, and make a cover to replace the eights panel with the 6x9s instead so it is open to the trunk and house the other speakers?</p><p></p><p>6. Its Oklahoma so trunk temps can get into 150+ easily so yea they are necessary. Twenty bucks and some time and that amp rack will stay cool I'll post pics when thru it'll be pretty cool</p><p></p><p>7. Yea I have the 5050 rgb 300 per 5m strip I'm gonna cut and solder and make jumps throughout the trunk and cabin</p><p></p><p>RCA spot was temporary</p><p></p><p>HU will prolly be first upgrade then a mini dsp, then start all over with the rest upgrading one thing at a time</p><p></p><p>All I can say is thank you for your help if you know anyone near Tulsa Oklahoma who can help with setup and tuning lemme know</p></blockquote><p></p>
[QUOTE="chefzane, post: 8105056, member: 654412"] A. Yes own sealed box B. No not using the single C. Yes its sealed 1. Yes I plan on fusing both ends in between battery's and fusing each 4 or 8 gauge run in between distro and amp, should I fuse the neg in between battery's and in between distro and amp also? 2. What should I use instead of y cables to go from two sets to four sets? Or just from one set to two cuz the xover only has three outs so I can just split one of those? I don't like y cables cuz ur basically splitting the voltage too right? 3. 6x9s and a set of tweets or two more component sets just diff size from what I already have. I can put them a couple places like in the kicks or in the doors if two more comp sets or move the eights to under front seats and put those in the rear deck box or eights to kicks but that's a ***** or in the front dash I dunno 4. What order does it go I know CLD on inside door skin, seal the door, then CCF, then MLV, then door panel? 5. What if I cut the back out of the box, turn the subs, then use the trunk area as the sealed portion or infinite baffle type setup? I don't have enough clearance to mount them between the seat and face of box, unless I cut it out and try to move it in making a small box smaller? What about a large slot behind 8" panel? Or move the eights, cut holes in that box, and make a cover to replace the eights panel with the 6x9s instead so it is open to the trunk and house the other speakers? 6. Its Oklahoma so trunk temps can get into 150+ easily so yea they are necessary. Twenty bucks and some time and that amp rack will stay cool I'll post pics when thru it'll be pretty cool 7. Yea I have the 5050 rgb 300 per 5m strip I'm gonna cut and solder and make jumps throughout the trunk and cabin RCA spot was temporary HU will prolly be first upgrade then a mini dsp, then start all over with the rest upgrading one thing at a time All I can say is thank you for your help if you know anyone near Tulsa Oklahoma who can help with setup and tuning lemme know [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
2000 mercury mystique-first ever custom install and need advice
Top
Menu
Home
Refresh