1996 Buick Regal Question

[blaze383]

The front valve cover gasket on my Regal is leaking a little bit of oil down to the exhaust manifold causing an oil burning smell....I have the new gasket and I want to replace it, I was wondering if anyone had a run through process on this and could give me some help or maybe a Haynes manual attachment to guide me....any help appreciated, thanks //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

Click to read more...

 

[4OZGLOVES 10+ year member]

The front valve cover gasket on my Regal is leaking a little bit of oil down to the exhaust manifold causing an oil burning smell....I have the new gasket and I want to replace it, I was wondering if anyone had a run through process on this and could give me some help or maybe a Haynes manual attachment to guide me....any help appreciated, thanks //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

Drain the oil.and look for the small bolt heads and remove the small bolts holding the valve cover on. Next take off the valve cover and remove the gasket,it may be rubber or it maybe a composite cork type material.If it is a cork type gasket make sure to scrape off the remaining gasket,get a can of gasket sealant lightly spray the gasket(if it's cork type) lay it down line it up and put the valve cover back on.Should be a 20 minute job if you are efficient about it.

 

[blaze383]

Drain the oil.and look for the small bolt heads and remove the small bolts holding the valve cover on. Next take off the valve cover and remove the gasket,it may be rubber or it maybe a composite cork type material.If it is a cork type gasket make sure to scrape off the remaining gasket,get a can of gasket sealant lightly spray the gasket(if it's cork type) lay it down line it up and put the valve cover back on.Should be a 20 minute job if you are efficient about it.

Lol good guiding, and I should have explained a little better, if I were to take a picture of the motor surrounding would u know if I should be able to get around half the shit covering the valve cover or am I gonna have to take all this junk off? There are motor mounts and im not sure if I can get around them or the plug wire mounting thing...

 

[4OZGLOVES 10+ year member]

is it a 3.1 or a 3.8

 

[blaze383]

is it a 3.1 or a 3.8

3.8.....Im not much 4 working on cars but I told myself I could fix it and I just dont wanna get half way through it and be stuck.

 

[4OZGLOVES 10+ year member]

I'll see if I have any 3.8 at my dealership and have a look.

 

[blaze383]

I'll see if I have any 3.8 at my dealership and have a look.

Thank ya sir....i'll post pics of what I am wondering about in a few to see if that will help me get started quicker.

 

[4OZGLOVES 10+ year member]

i'm assuming it is the 3800 series,if I am correct,first you need to remove the plastic cover,next if you are looking at the engine bay frome the front you are gonna have a 2 front mounts one on the left and one on the right.You will need to remove the LEFT side,after removing the left side the distributer mount will come right off,from there just follow the instructions from post 2.The motor will be just fine being supported by the right mount and the rear mount.

 

[eutechnyx 10+ year member]

I dont see a point In draining the oil,but to each his own.

 

[blaze383]

i'm assuming it is the 3800 series,if I am correct,first you need to remove the plastic cover,next if you are looking at the engine bay frome the front you are gonna have a 2 front mounts one on the left and one on the right.You will need to remove the LEFT side,after removing the left side the distributer mount will come right off,from there just follow the instructions from post 2.The motor will be just fine being supported by the right mount and the rear mount.

Yea thats wat I figured I had to do, I dont have a floorjack to take tension off the mount and I assumed I do so I just took it somewhere and they are doing it for $30 bucks and I kinda need my car asap but thanks for all your input man.

I dont see a point In draining the oil,but to each his own.

It is due an oil change but I wanted to get this done first, Hopefully will have it in the morning to change it myself //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[15nissen 10+ year member]

I dont see a point In draining the oil,but to each his own.

Agreed, no reason to drain the oil. Make sure that the motor is cold, so you know most of the oil drained back to the crankcase / pan.