Recent content by SC4

F I just set my gains on lunch and they are at ~19 for channels 1&2 Would the double din I bought be a "lesser quality deck"? I had a prs-80 but I planned on going with a bit ten or something later on so I didnt want all the processing done on the HU itself, and I like the looks and...

at noon I will get a comprehensive list of settings and get back on here and my tuning volume is typically around 25 ish, im gonna run an android RTA and adjust my eq on lunch at a higher volume this time and see where that gets me.

I drilled and through bolted to the tub of the hatch area, and I did scratch the paint off. My settings have changed through the time I've had the setup usually everything is flat with a small boost to my 50hz range, no LOUD setting on my stereo is in my first post kenwood ddx-370 not sure...

I attached a bolt to the inside of the tub for the spare   ---------- Post added at 02:57 PM ---------- Previous post was at 02:57 PM ----------   My bad wrong number its the reference 4.760 REF4.760 - Reference - Amplifiers - Car Audio

Tonight I'm going to try regrounding the HU and also installing 4 channel rca's

Ok Here is the setup kenwood ddx-370 headunit soundstream ref 740 amp sony gs-1720s midwoofers alpine type spr-10tw tweeters I have a set of rca's from my headunit to my amp then at the amp im using it in 4 channel mode to split channel 3&4 to strictly bass frequencies Ive got channels...

No not the input basically I had my sub unplugged @ the sub and I was hooking up my crossover on channel one so I grab what I thought was the speaker wire from my crossover and plug it in to channel 1 and the amp goes into protect and shuts off......I hooked up my 3 and 4 channels output bridged...

Alright I think I messed something up, my ******* lost track of a wire and ran my channel 3&4 bridged right into channel 1. There is a pretty bad whine only through channel 1 now and I hooked up my multimeter on channel 1 & 2 to set gains and channel 1 was only putting out about 1v...

Yea I guess I could have worded it differently, I do understand this sir. I'm active and bi-amped so for my setup I described it correctly but worded it as if they were the same. Thank you for the clarification

btw the reason I am just sending them back is the headunit could only be returned to amazon until the 31st of january so I just went with it

Mids were bandpassed @ 100hz 18 db slope and up to 5k 18db slope the highs were crossed over @ 5k w/ a 24 db slope, but my crossover points are something ive been messing with so its never constant. I removed the head unit and the amp and I am sending them both back. The amp doesn't give me...

Ok I didnt think about that the DMM is a good idea. By Bi-amped I mean 4 channels I'm running highs on the A bank (2 tweeters/2 channels) and mids on the B bank (2 drivers/2 channels) Active front stage is another way to say it, im actively crossing over the signal @ the headunit, rather than a...

If you read the original post I have reset the head unit's processor as well as audio setting to no avail. Also Bi amped means I have a channel for each speaker in my component set the head unit supports 2 way plus sub active crossover network so Im running one channel to each 6.5" mid bass...

Hey, really appreciate the assistance man, let the troubleshooting begin I guess! I was sitting here all day like wtf, no one is going to say anything? so again very much appreciated! I will definitely keep this updated as I figure things out. I thought this at first as the driver side sounded...

My setup: Pioneer DEH-80PRS Sony Components xs-gs1720s actively bi-amped kenwood kac240s So last night I'm cruising on back road's, going to pick up my gf, and blaring fairies wear boots by black sabbath when all of a sudden my driver side speakers get very cloudy, higher pitched, and loud...