Recent content by Rukuzz

Thanks SoCalBean420. I've looked at those but you know ebay stuff.....I e-mailed a company online which sells refoam kits for JL but they said they didn't have the quality replacement required for my Sub. I've put out some questions to the ebay guys and will keep looking online.

Anyone know where I can get a good replacement for this speaker. It's separated from the cone about 5 inches. I don't think I can just glue it back because it has a piece coming off it. I have two on my truck and they worked great. I'd hate to drop more $$$ on a new sub if this can be fixed...

NOTED! But it goes without saying if you don't want to be bothered by it then don't bother with it. As for the setup well I've checked this thing back and forth and can't find a thing. Secondly, even if the gains were on max how would that make any noise and kill the amp outs. I don't get it...

IF YOU DON'T LIKE IT DON'T READ IT OR POST ON IT!!! I already called JL and they are a bunch of excuses and time wasted. I'm trying to get responses from people who have had similar problems or know JL Products. Not people who waste their time complaining about a question.

BUMP! ANYONE?

Ok, so after a month of back and forth checking with JL to see if they could get me the 500/1. It's done! I've got it and I'm getting the same crappy sound. The amp hits great once it's past the distortion coming out. It sounds like an old vinyl record before it hits the song. I took apart...

At this point I would have no problem coughing up a lung!!! I'll pay the **** $400-$500 the 500/1 costs but gimme a break on the lemon. I've got no beef with JL. I'm sure they make quality amps. I buy stuff from them because they have proven quality at least to me. That's why my truck is...

Does anyone know why the outputs might be going out. I've checked my whole setup for from battery to amp over an over and I can't even find even a short. I'd really like to get a 500/1 to run a pair of 10W3v2 I just got. I was planning to use the 250/1 to run a pair of 10wO but I guess I'll...

Thanks for the replies guys! Excelerater, I wouldn't wish this lemon on my worse enemy. The only thing this is good for is as a door stop or a big arse paper weight!!!!!!!!!!!!!

I purchased a JL 250/1 amp a while back (Nov. of 2004) to run 2-10" JL subs. Six weeks after I got this thing the sub outputs on the amp went out. I've already sent it 3 times for repair through the authorized dealer I purchased it at and for the fourth time the outputs have gone out. I'm...

Thanks for all the replies guys! Unfortunately, Santa had no more than $600 to cover the subs and amp. (on credit). $500+ would've got me the amp only and no subs, then I'd probably bust the JL10WOs I had before. Now those are going on another ride for continued pleasure. I'm not a audio...

I've got 2-JL10W3V2-4 each in sealed 1.21 cu.ft. boxes. I will be running these in series with a 250/1? And, thanks but no I will not be getting a stronger amp. I want the best quality bass possible. I'm not going for loudness just the best butt bruising bass possible. I've run an excel...

If i go ported JL asks for 1.25 cu. ft. Plus I thought better bass came from sealed & loudness from ported?

I've got a couple of individual boxes that I created using one of the excel worksheets here for 2 JL 10WO8s. Each box has at least 1.21 c.u. ft. of. I recently purchased 2 JL 10W3V2-4s and stuck them on the same boxes. Will this be enough c.u. ft? JLs specs for the W3 & WOs is around...

I think I've found the culprit. In my case, and only in my case, it was the amp. JL's amp just went caput! I replaced the 8 guage wire with 4 this weekend and hooked up my speakers in series they played for a little while then I shut it down to do some clean up. I went back and turned it on...