Recent content by Graves

https://drive.google.com/file/d/1n6pUGYOI3jc9bCBCHu4fFygCLABYmJHe/view?usp=sharing for anyone who comes across this thread also looking. Or this thread can be deleted.

I know it would be a hassle to find and upload it if you had it kicking around, id pay you for your trouble.

I'm looking for the Alpine Imprint V2.10 for the PXA-H100. My wife got rid of all my "computer stuff" when we were seperated. I've done an exhaustive search for it and all I have found is a dead torrent and links to malware. It looks like I can just order the microphone kit and get it...

Thanks! Thats the motivation I need! I was even thinking I can sell the 6x9's to help buy a tweeter amp because the four channel would put out to much power even with the gains at minimum. I was thinking in the mean time I can run the wire because why not? do an A/B comparison (three-way...

if I were to go fully active would I get an appreciable SQ benefit in my current system? So from my pxa-h100 DSP I am three way active with: my rear coaxial 6x9s being being band passed seeing between 63-5k hertz (the amp was oddly going into protection mode when sending them a moderate amount...

Okay, made some progress,! pretty much had it troubleshooted to the speakers, raising the crossover point had not helped and I was about to add a tweeter in series to see if the amp would be happier with more Impedance. But I got the idea to put a low bass filter on, they have a high pass...

of Course but... he did so with the volume all the way up... and that amp has speaker level imputs.

Okay, sounds like you Got it troubleshooted. When every thing is ready to go check that you are still getting ac volts at the ends of the rcas when they are going to be plugged into the deck. It sucks if you got a bad amp from the pawn shop they usually won’t take anything unless it can be...

http://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=2&toolid=10001&campid=5335951755&icep_item=283494243635 shop radio? I think something like that would go best in a classic ferarri or something, with a dsp and plenty of power:cool:

so I have never heard one personally, but i would Like to. I think it is really cool. I dont care about production year i care about does it do a good job. Maybe ignorance is bliss but I have been happily pushing my old alpine mrv-1505 hard everyday for 20 years and I am proud af. i got...

So I love my system, I’ve had my alpine ida-x305s with pxa-h100 dsp and pdx f4 amp for a while, They have seen many cars and many speakers over the years. (Alpine mrv-1505 and IDMAX sub in case you were wondering) so I had a set of image dynamics ctx 6x9 coaxials that i lost the tweeters on...

so gain doesn’t matter when checking the RCA’s, we want to do an AC voltage check on the RCA ‘s when you unplug them from the amp, maybe with a test tone playing (at least something playing) the. If you get a zero reading there then check the back of the head head unit, you should be seeing AC...

For starters you could use your DMM on AC volts and let us know what the RCA volts and amp voltage across the speaker terminals for more information. If you don't have any voltage coming from the RCA's check your deck's settings if it has an option, like mine does, to turn off subwoofer etc.

OP, it doesn't matter that the amp only draws 40 amps full tilt for very brief moments. The 200 amp fuse is to protect the wiring. If there is a short, what will give out first the 200 amp fuse or the wiring to your fuse box terminal? Because it looks to me like the wiring to the fuse box...

Yes, if you have two 4 ohm voice coils ran in parallel you have a 2 ohm total load the amp sees. (30 volts AC) Yes you want to measure the same spots (bridged) you hook up your speaker wires to. I don't know what bass extension is, is that adjusting Q factor or EQ boosting something...