Recent content by djk

I've searched through the old threads on baffles and there seems to b mixed opionon on whether or not I should install them. So should I or shouldn't I? What do you guys think? If so, should I use foam or PVC, or doesn't it matter? Also, should I cut off the back of the baffles?

I have a pair of JL Audio TR650 speakers which I am not happy with and I am looking for new 6.5 coaxial speakers. My top candiate is Phoenix Gold Tantrum tx6.5c speakers. Has anyone heard these speakers? I was thinking of going with them since I have tantrum subs and amps and are happy with...

I need to raise by 6x9 about 3/4" off the rear deck so that my trunk will close. Anybody kow where I can purchase some pre-cut for 6x9 3/4 in wood. Also, my 6.5 front speakers didn't mount real well and I'd like to mount them onto a wood frame for a more solid install. If they do not sell...

The diamond seems to be the best but the TM3 seems hard to get. Anyone know where I can get one? Even my local dealer didn't have them. They only had the CM3. Also, the PG TX10 would match my tantrum amps really well. Anyone hear these subs?

Here is what I have narrowed it down to: Diamond Audio TM3 10" Phoenix Gold TX10D Crystal CSe 10.4 10" Subwoofer SoundStream PCS-10 10" Picasso Series Woofer Soundstream EGW-10 Let me know what you think

OK. I just ordered my amp, a 200 watt PG T200.2. And I have my enclosure (.75 sealed.) http://www.circuitcity.com/detail.jsp?c=1&b=g&u=c&catoid=-11261&qp=0&oid=69720&m=0 Now all I need is a sub. I am thinking of a Diamond Audio 10" TM3. Anybody ever hear these? Any...

So would you say it is worth $40 extra for the tantrum?

So if they are no matter should I still go for the Tantrum? Will it sound better/loader? Be more reliable? I have already ordered my T200.2 for my sub amp and they give a rating of 200W@4 ohms but none at 2 ohms bridged. Can it do this? Also, if I get a 4 ohm sub with a DVC can I run it at...

OK. So I don't have to worry about the power dropping too much if the battery isn't putting out enough power. I noticed the Octane owners manual just gives the 14.4 rating. Is there any way I might be better off with the Octane Series (R5.0:4) than the Trantrum? It's about $40 cheaper too:)

Thanks. One more question. The owners manual say 4x20 at 12.5V and 4x50 at 14.4V. How do I know what my car is feeding it? How can I make sure it's 14.4V? 4x20 sounds awfully low.

Oohh. thanks. And the frequency selector works both, right? I am planning on running the 8 gauge to a T200.2 in bridged mode. Will that be alright?

I am about to purchase this amp and have a few questions? 1.) The owners manual says to run 4 gauge wire for + and ground. I have 4 gauge to a splitter, and then 8 gauge to the amp. The ground is 8 gauge. Will this be OK for a 4x50 amp? 2.) After looking at the owners manual, it doesn't...

Sounds nice to me. Jmac, do you remember the size of the enclosure you made for that sub? Also, what were the fronts running at? I'm thinking of 4x50. Will the 250.2 overpower a 4x50?

So would a Tantrum 250.2 to a PG ti10 sub be better than a Xtant A3001 to a JL 10w0? I looking for mostly SQ. Also, anyone know how to get that ti10d deal on thezeb.com?

Anyone??? Was the Octane a replacment for the Tantrum or is it a lower line than the Tantrum was? What would be better, an Octane 4x50(Octane 5.0:4) or a Tantrum 4x50(T400.4)