Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
X-over and input volt questions
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="KoG" data-source="post: 8663778" data-attributes="member: 676156"><p>I have 2018 Camaro SS 1LE non-Bose, no factory amp. </p><p></p><p>Here's my setup: I am planning to use the PAC AP4-GM61 module to get the RCA clean-signal output straight from the 8" factory HU. It will then hooked on to the Rockford Fosgate P1000X5 amp via the RCA.</p><p></p><p>The output to the speakers will be:</p><p></p><p>FRONT: RF P165-SI components with x-over built into the basket of the woofers/tweeters.</p><p></p><p>1) Now here's my question, on the amp it has LP - AP - HP. Do I set it to AP since the x-over are built in the speakers? or should I still set it HP?</p><p></p><p>REAR side panels: RF P1650 Coaxial 2-Way</p><p></p><p>2) This would be set it to AP also?</p><p></p><p>SUB: I haven't fully decide on which sub I want but it will be a ported enclosure. Obviously this channel will be set to LP.</p><p></p><p>3) On the amplifier, there are knobs for FRONT and REAR input level: 12.0V to 0.15V. How do I know where to set this at?</p><p></p><p>EDIT: The manual for the PAC-GM61 states, “AP4-GM61 delivers variable 5v RMS pre-amp outputs with fading.” I would set it at 5V. I believe there’s a 4V on the dipswitch too.</p></blockquote><p></p>
[QUOTE="KoG, post: 8663778, member: 676156"] I have 2018 Camaro SS 1LE non-Bose, no factory amp. Here's my setup: I am planning to use the PAC AP4-GM61 module to get the RCA clean-signal output straight from the 8" factory HU. It will then hooked on to the Rockford Fosgate P1000X5 amp via the RCA. The output to the speakers will be: FRONT: RF P165-SI components with x-over built into the basket of the woofers/tweeters. 1) Now here's my question, on the amp it has LP - AP - HP. Do I set it to AP since the x-over are built in the speakers? or should I still set it HP? REAR side panels: RF P1650 Coaxial 2-Way 2) This would be set it to AP also? SUB: I haven't fully decide on which sub I want but it will be a ported enclosure. Obviously this channel will be set to LP. 3) On the amplifier, there are knobs for FRONT and REAR input level: 12.0V to 0.15V. How do I know where to set this at? EDIT: The manual for the PAC-GM61 states, “AP4-GM61 delivers variable 5v RMS pre-amp outputs with fading.” I would set it at 5V. I believe there’s a 4V on the dipswitch too. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
X-over and input volt questions
Top
Menu
Home
Refresh