Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
Upgrading my budget system [Help Wanted] 6/29/2016
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Jeffdachef" data-source="post: 8512676" data-attributes="member: 650438"><p>If you go dsp which costs a lot more, your results can be a lot better than most head unit setups on the market. If you put like 10+ hours of tuning into it. Usually 3 way front stage actuve capable plus subwoofer. Which means you can crossover midbass, midrange, tweeter and subwoofer along with time aligning each driver individually and individual EQ as well. Basically complete control ofver your audio setup which allows for a perfect tune if tuned right. Its very extensive and has a pretty big learning curve.</p><p></p><p>All you need to add one is the dsp itself, pc, the speaker drivers and the amp.</p><p></p><p>2 way active will just be tweeters and mids so a 4 channel amp would be adequate and would require 3 pairs of rcas from dsp to monoblock and 4 channle. 3 way active which is midbass, midrange and tweeter, youll need a 6 channel amp or a 4 channel amp and a smaller 2 channel for the tweeters. About 4 pairs of rcas needed for this</p><p></p><p>You will get signal from your current head unit(no need to swap) via one pair of RCA to the dsp, then with proper amount of rcas to the amps. Youll need to run wires for power, ground and remote. Then you tune with the PC. Thats it.</p></blockquote><p></p>
[QUOTE="Jeffdachef, post: 8512676, member: 650438"] If you go dsp which costs a lot more, your results can be a lot better than most head unit setups on the market. If you put like 10+ hours of tuning into it. Usually 3 way front stage actuve capable plus subwoofer. Which means you can crossover midbass, midrange, tweeter and subwoofer along with time aligning each driver individually and individual EQ as well. Basically complete control ofver your audio setup which allows for a perfect tune if tuned right. Its very extensive and has a pretty big learning curve. All you need to add one is the dsp itself, pc, the speaker drivers and the amp. 2 way active will just be tweeters and mids so a 4 channel amp would be adequate and would require 3 pairs of rcas from dsp to monoblock and 4 channle. 3 way active which is midbass, midrange and tweeter, youll need a 6 channel amp or a 4 channel amp and a smaller 2 channel for the tweeters. About 4 pairs of rcas needed for this You will get signal from your current head unit(no need to swap) via one pair of RCA to the dsp, then with proper amount of rcas to the amps. Youll need to run wires for power, ground and remote. Then you tune with the PC. Thats it. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
Upgrading my budget system [Help Wanted] 6/29/2016
Top
Menu
Home
Refresh