Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
Amplifiers
Taramps smart 3 shutting off. Voltage drop?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="CNB83" data-source="post: 8709586" data-attributes="member: 680309"><p>Hi, I recently purchased a Taramps Smart 3 and wired it to my FI SSD Neo DVC2 @ 1ohm. It shuts off giving me the <9v light on the monitor. I did a voltage test at my amp and battery (alt to hard to get to) and when the kick hits I do see the meter drop to 11ish volts before the amp shuts off. Is my 140amp alt not enough for this? Would a 250amp do? Is my 100amp fuse in the power line the issue? Should I wire it down to 4ohms? Also I noticed when it does hit, kinda sounds weak on the lows, kicks and highs hit loud. My alpine Mrx-m110 hit way louder just using 1 coil (i know I shouldn't have done that) @2ohms. Even my old 350rms amp powering a Alpine Type-R hit better lows. I've also been seeing something about Taramps not liking 5V outputs? My HU is a Alpine CDA-9886. I was a little weary on purchasing a brand I've never heard of but I did, and now I'm regretting it because my audio is terrible. Please, any help is appreciated. Thank You.</p></blockquote><p></p>
[QUOTE="CNB83, post: 8709586, member: 680309"] Hi, I recently purchased a Taramps Smart 3 and wired it to my FI SSD Neo DVC2 @ 1ohm. It shuts off giving me the <9v light on the monitor. I did a voltage test at my amp and battery (alt to hard to get to) and when the kick hits I do see the meter drop to 11ish volts before the amp shuts off. Is my 140amp alt not enough for this? Would a 250amp do? Is my 100amp fuse in the power line the issue? Should I wire it down to 4ohms? Also I noticed when it does hit, kinda sounds weak on the lows, kicks and highs hit loud. My alpine Mrx-m110 hit way louder just using 1 coil (i know I shouldn't have done that) @2ohms. Even my old 350rms amp powering a Alpine Type-R hit better lows. I've also been seeing something about Taramps not liking 5V outputs? My HU is a Alpine CDA-9886. I was a little weary on purchasing a brand I've never heard of but I did, and now I'm regretting it because my audio is terrible. Please, any help is appreciated. Thank You. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Amplifiers
Taramps smart 3 shutting off. Voltage drop?
Top
Menu
What's new
Forum list