Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
CarAudio.com Classifieds
Car Audio Classifieds
Rf p400/4
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="04murdalanche" data-source="post: 8033768" data-attributes="member: 637570"><p>Thanks man, no use for it. Would rather just give it to someone else that needs it, nice little amp here's some info on it</p><p></p><p>50 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms)</p><p></p><p>200 watts RMS x 2 at 4 ohms (4-ohm stable in bridged mode)</p><p></p><p>variable high-pass/low-pass crossover (40-400 Hz, 12 dB/octave)</p><p></p><p>variable Punch Bass boost (0-18 dB at 45 Hz) with remote</p><p></p><p>CEA-2006 compliant</p><p></p><p><strong>Tri-way capable (Tri-Way crossover required)</strong></p><p></p><p>MOSFET power supplies and output stages</p><p></p><p>MEHSA transfers heat efficiently from the MOSFET devices to the heat sink for high performance</p><p></p><p>TOPAZ eliminates ground loop noise</p><p></p><p>trans-ANA circuitry keeps preamp signal clean</p><p></p><p>NOMAD "intelligent" protection circuitry</p><p></p><p>preamp outputs</p><p></p><p>16-7/16"W x 2-3/4"H x 11-1/4"D</p></blockquote><p></p>
[QUOTE="04murdalanche, post: 8033768, member: 637570"] Thanks man, no use for it. Would rather just give it to someone else that needs it, nice little amp here's some info on it 50 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms) 200 watts RMS x 2 at 4 ohms (4-ohm stable in bridged mode) variable high-pass/low-pass crossover (40-400 Hz, 12 dB/octave) variable Punch Bass boost (0-18 dB at 45 Hz) with remote CEA-2006 compliant [B]Tri-way capable (Tri-Way crossover required)[/B] MOSFET power supplies and output stages MEHSA transfers heat efficiently from the MOSFET devices to the heat sink for high performance TOPAZ eliminates ground loop noise trans-ANA circuitry keeps preamp signal clean NOMAD "intelligent" protection circuitry preamp outputs 16-7/16"W x 2-3/4"H x 11-1/4"D [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
CarAudio.com Classifieds
Car Audio Classifieds
Rf p400/4
Top
Menu
Home
Refresh