Reply to thread

Message

<blockquote data-quote="thylantyr" data-source="post: 4010910" data-attributes="member: 560358">Why? //content.invisioncic.com/y282845/emoticons/crazy.gif.c13912c32de98515d3142759a824dae7.gif//content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif//content.invisioncic.com/y282845/emoticons/crazy.gif.c13912c32de98515d3142759a824dae7.gifHypothetical simplified.The output of you source is here -&amp;gt; Then it usually connects to a lowresistance resistor, lets say 50 ohms - 200 ohms.The input of your amplifier may be 10,000 ohms - 50,000 ohms typical.Put a cable in there to interface the source with amplifierSource [50 - 500 ohm output impedance] -&amp;gt; your cable -&amp;gt; Amplifier [10,000 - 50,000 ohms input impedance]Lets assume;Source [50 - 500 ohm output impedance] -&amp;gt; cheap cable is 10 ohms -&amp;gt; Amplifier [10,000 - 50,000 ohms input impedance]vs.Source [50 - 500 ohm output impedance] -&amp;gt; superman cable is 0 ohms &amp;gt; Amplifier [10,000 - 50,000 ohms input impedance]Compare the two scenarios. Follow the signal path.The signal comes out and get 50 ohms - 200 of resistance, then flows thrueither zero ohms or 10 ohms of resistance, then enters the amp with 10,000 - 50,000 ohms of resistance.Do you think that cable with zero or 10 ohms makes a difference? //content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gifWhen you analyze cables in signal path, you analyze it from a &#039;low pass&#039; filtereffect and since cheap cable already has low resistance, that isn&#039;t a variableunless you run thousands of feet or more.Read this,&nbsp; it&#039;s basic AC/DC electronic theory. Perhaps the first two classesyou take if you if you seek to understand electronics.<a href="http://www.rane.com/note126.html" target="_blank">http://www.rane.com/note126.html</a></blockquote>

[QUOTE="thylantyr, post: 4010910, member: 560358"] Why? [IMG]//content.invisioncic.com/y282845/emoticons/crazy.gif.c13912c32de98515d3142759a824dae7.gif[/IMG][IMG]//content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif[/IMG][IMG]//content.invisioncic.com/y282845/emoticons/crazy.gif.c13912c32de98515d3142759a824dae7.gif[/IMG] Hypothetical simplified. The output of you source is here -> Then it usually connects to a low resistance resistor, lets say 50 ohms - 200 ohms. The input of your amplifier may be 10,000 ohms - 50,000 ohms typical. Put a cable in there to interface the source with amplifier Source [50 - 500 ohm output impedance] -> your cable -> Amplifier [10,000 - 50,000 ohms input impedance] Lets assume; Source [50 - 500 ohm output impedance] -> cheap cable is 10 ohms -> Amplifier [10,000 - 50,000 ohms input impedance] vs. Source [50 - 500 ohm output impedance] -> superman cable is 0 ohms > Amplifier [10,000 - 50,000 ohms input impedance] Compare the two scenarios. Follow the signal path. The signal comes out and get 50 ohms - 200 of resistance, then flows thru either zero ohms or 10 ohms of resistance, then enters the amp with 10,000 - 50,000 ohms of resistance. Do you think that cable with zero or 10 ohms makes a difference? [IMG]//content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif[/IMG] When you analyze cables in signal path, you analyze it from a 'low pass' filter effect and since cheap cable already has low resistance, that isn't a variable unless you run thousands of feet or more. Read this, it's basic AC/DC electronic theory. Perhaps the first two classes you take if you if you seek to understand electronics. [URL="http://www.rane.com/note126.html"]http://www.rane.com/note126.html[/URL] [/QUOTE]

Verification