Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Psi vs. dd audio recone kit?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="sharkman" data-source="post: 8314356" data-attributes="member: 661488"><p>So I'm trying to recone a 18 inch dd motor . The box size is 9.2 cubic feet and tuned at 32 in my 90 bronco...as far as power I'm not sure yet.. I was thinking a brx 2400 and a xs d3400</p><p></p><p>This is from psi</p><p></p><p>&gt;The estimated cost to build a recone kit using the extremely oversized Z series surround, a flatwound XL voice coil, 4 spiders, and dual sewn lead wire with 8gauge direct connect wiring would be $200.</p><p></p><p>&gt;</p><p></p><p>&gt;-----Original Message-----</p><p></p><p>&gt;From: Dantone sharkey [mailto<img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite8" alt=":D" title="Big grin :D" loading="lazy" data-shortname=":D" />antonesharkey55@gmail.com]</p><p></p><p>&gt;Sent: Saturday, September 06, 2014 10:28 AM</p><p></p><p>&gt;To: <a href="http://mailto:" target="_blank">info@fixmyspeaker.com</a></p><p></p><p>&gt;Subject: FixMySpeaker Service Request - (1) DD audio 9500 18 inch Dual</p><p></p><p>This is from dd</p><p></p><p>The tuning on that is perfectly fine. *The 9512 I run daily is tuned at 30hz, and has been for quite some time. *You're enclosure is on the large side, we typically recommend using our 18's in 5-7 cubic feet per driver.</p><p></p><p>We would ask that the driver be sent in for service. *There are lots of small changes made in these older DD models. *We ask that they be sent to us for recone so that we can insure that all the new 2014 parts fit into your 13 year old woofer. *Basic rebuild at the DD facility is only $330. *You'll get our newest 8 spoke basket to give you a larger spider landing for improved excursion and linearity. *That $330 will also include the shipping back to you. *If you want to get one loaded, we can build them up quite a bit. *We can add full carbon diaphragm and dust cap, we can change the spider composition to a stiffer pack to work better in the enclosure you're using, we can do full reinforcements on all the joints attaching to the former to make the driver stronger, or we can also add a flat wind aluminum voice coil. *If you check all the proverbial boxes, your in house recone can run upwards of $1050.</p><p></p><p>The only limitations are the ones you set //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif*</p><p></p><p>Aaron Trimble</p><p></p><p>Digital Designs</p><p></p><p>1141 NW 1st St.</p><p></p><p>Oklahoma City, OK, 73106</p><p></p><p>405-239-2800</p></blockquote><p></p>
[QUOTE="sharkman, post: 8314356, member: 661488"] So I'm trying to recone a 18 inch dd motor . The box size is 9.2 cubic feet and tuned at 32 in my 90 bronco...as far as power I'm not sure yet.. I was thinking a brx 2400 and a xs d3400 This is from psi >The estimated cost to build a recone kit using the extremely oversized Z series surround, a flatwound XL voice coil, 4 spiders, and dual sewn lead wire with 8gauge direct connect wiring would be $200. > >-----Original Message----- >From: Dantone sharkey [mailto:Dantonesharkey55@gmail.com] >Sent: Saturday, September 06, 2014 10:28 AM >To: [URL="mailto:"]info@fixmyspeaker.com[/URL] >Subject: FixMySpeaker Service Request - (1) DD audio 9500 18 inch Dual This is from dd The tuning on that is perfectly fine. *The 9512 I run daily is tuned at 30hz, and has been for quite some time. *You're enclosure is on the large side, we typically recommend using our 18's in 5-7 cubic feet per driver. We would ask that the driver be sent in for service. *There are lots of small changes made in these older DD models. *We ask that they be sent to us for recone so that we can insure that all the new 2014 parts fit into your 13 year old woofer. *Basic rebuild at the DD facility is only $330. *You'll get our newest 8 spoke basket to give you a larger spider landing for improved excursion and linearity. *That $330 will also include the shipping back to you. *If you want to get one loaded, we can build them up quite a bit. *We can add full carbon diaphragm and dust cap, we can change the spider composition to a stiffer pack to work better in the enclosure you're using, we can do full reinforcements on all the joints attaching to the former to make the driver stronger, or we can also add a flat wind aluminum voice coil. *If you check all the proverbial boxes, your in house recone can run upwards of $1050. The only limitations are the ones you set [IMG]//content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif[/IMG]* Aaron Trimble Digital Designs 1141 NW 1st St. Oklahoma City, OK, 73106 405-239-2800 [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Psi vs. dd audio recone kit?
Top
Menu
Home
Refresh