Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Pro Installers: Need help badly!!!!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Frankensuby" data-source="post: 2252867" data-attributes="member: 569869"><p>I am getting tired and frustrated with the car I am currently installing a system in. I have all the wiring run, and everything installed. Since the first time I installed the amps, specifically a speaker amp (Power Acoustik PS4-240), I had noise come through the speaker. At first, it was even with the engine off and HU off. I seemed to have eradicated that problem with the engine off, but now I have really bad engine whine coming through the speaker amp when the engine is on.</p><p></p><p><strong>Wires run</strong>: The wires are run with the power and the remote going down the middle of the car (underneath console), 2 sets of RCA's down the left side, and one set run down the right. I have a 4 gauge power cable running back to a distribution block, splitting the power to 2-8 gauge wires, powering the amp.</p><p></p><p><strong>Amp setup</strong>: Both amps are screwed to the back of the seats, with both being grounded to the 2 bolts holding down the rear set (underneath). I cleaned up the 2 ground spots greatly. The grounds were upgraded to 2 sets of 4 gauge instead of the original 8 gauge when the noise became an issue.</p><p></p><p><strong>Amps</strong>: Mono Pioneer GM7200 ; Power Acoustik PS4-240 speaker amp</p><p></p><p>I have cleaned up all the ground spots in the entire car. I went over the engine bay today and cleaned up every ground spot I found. To no avail, in fact, It almost seemed louder.</p><p></p><p>I really need help with this. I installed my own similar setup in my car, and had 0 issues like this. I have followed the same exact routine I did with my car.</p><p></p><p>Possible theories:</p><p></p><p>1. Ground loop? I have cleaned up all grounds, but nothing is working.</p><p></p><p>2. HU ground? Is it possible that the HU might not be ground correctly and it is finding the ground through the RCA's?</p><p></p><p>3. The ground points for my amps are bolted to the same framework for the seat, but on opposite sides. Would this cause any issues?</p><p></p><p>4.Solution: Big 3? I bought everything for the Big 3, all I have to do is install. Would this help greatly?</p><p></p><p>5. Solution: Inverter(?): Some guys on here suggested something that eliminates the ground loop or interference by putting it in-line...?</p><p></p><p>The car is a 1998 Subaru Legacy, for anyone who has one or who has worked on them in the past.</p></blockquote><p></p>
[QUOTE="Frankensuby, post: 2252867, member: 569869"] I am getting tired and frustrated with the car I am currently installing a system in. I have all the wiring run, and everything installed. Since the first time I installed the amps, specifically a speaker amp (Power Acoustik PS4-240), I had noise come through the speaker. At first, it was even with the engine off and HU off. I seemed to have eradicated that problem with the engine off, but now I have really bad engine whine coming through the speaker amp when the engine is on. [B]Wires run[/B]: The wires are run with the power and the remote going down the middle of the car (underneath console), 2 sets of RCA's down the left side, and one set run down the right. I have a 4 gauge power cable running back to a distribution block, splitting the power to 2-8 gauge wires, powering the amp. [B]Amp setup[/B]: Both amps are screwed to the back of the seats, with both being grounded to the 2 bolts holding down the rear set (underneath). I cleaned up the 2 ground spots greatly. The grounds were upgraded to 2 sets of 4 gauge instead of the original 8 gauge when the noise became an issue. [B]Amps[/B]: Mono Pioneer GM7200 ; Power Acoustik PS4-240 speaker amp I have cleaned up all the ground spots in the entire car. I went over the engine bay today and cleaned up every ground spot I found. To no avail, in fact, It almost seemed louder. I really need help with this. I installed my own similar setup in my car, and had 0 issues like this. I have followed the same exact routine I did with my car. Possible theories: 1. Ground loop? I have cleaned up all grounds, but nothing is working. 2. HU ground? Is it possible that the HU might not be ground correctly and it is finding the ground through the RCA's? 3. The ground points for my amps are bolted to the same framework for the seat, but on opposite sides. Would this cause any issues? 4.Solution: Big 3? I bought everything for the Big 3, all I have to do is install. Would this help greatly? 5. Solution: Inverter(?): Some guys on here suggested something that eliminates the ground loop or interference by putting it in-line...? The car is a 1998 Subaru Legacy, for anyone who has one or who has worked on them in the past. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Pro Installers: Need help badly!!!!
Top
Menu
Home
Refresh