Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
Amplifiers
power acoustik amp HELP
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="subzero" data-source="post: 7257264" data-attributes="member: 600350"><p>NO. we know what you are running. YOur not the first person to use a four channel amp that way.</p><p></p><p>You will wire it up and get 2 chanels @ 100watts rms at 4 ohms. and that is probly going to be even less according to the volume levels</p><p></p><p>When you bridge the rear channel you will only get 250watts rms @ 4 ohms. and that will probly be less as well. And it will definately be less than your recomended 600watts rms for that subs. (I assume you only have one sub?)(I hope)</p><p></p><p>If you bridge that amp and run it at 2 ohms it might get hot and shut down. With a dual 4 ohm sub, the only wiring options you have are 8 ohms and 2 ohms and that amp doesnt say it is 2 ohm stable in a mono bridge.. So, what I suggest is that you go buy a better amp for your sub.</p><p></p><p>sub specs</p><p></p><p>Sensitivity: 84 dB</p><p></p><p>RMS Power Range : 600 Watts</p><p></p><p>Peak Power Handling: 1200 Watts</p><p></p><p>Impedance: Dual 4 Ohm</p><p></p><p>Low Frequency response: 30 Hz</p><p></p><p>High Frequency Response: 400 Hz</p><p></p><p>Diameter: 12 Inch</p><p></p><p>amp specs</p><p></p><p>Gothic Series 4-Channel Car Amplifier</p><p></p><p>RMS Power Rating:</p><p></p><p><span style="color: red">4 ohms: 100 watts x 4 chan. </span></p><p></p><p><span style="color: red">2 ohms: 125 watts x 4 chan. </span></p><p></p><p><span style="color: red">Bridged, 4 ohms: 250 watts x 2 chan. </span></p><p></p><p><span style="color: red">Max power output: 1200 watts </span>MOSFET power supply</p><p></p><p>Pulse width modulation circuitry</p><p></p><p>Remote bass level input (remote level control sold separately)</p><p></p><p>LED power indicators</p><p></p><p>Bass Boost (0-18 dB bass boost at 45 Hz)</p><p></p><p>Tri-Mode capable</p><p></p><p>4/3/2 channel operation</p><p></p><p>2 Ohm stereo, 4 ohm mono stable</p><p></p><p>Preamp RCA outputs</p><p></p><p>Low level inputs (200mV-8V)</p><p></p><p>Variable high-pass filter (40-250 Hz, 12 dB/octave)</p><p></p><p>Variable low-pass filter (40-250 Hz, 12 dB/octave)</p><p></p><p>Frequency response: 10-30,000 Hz</p></blockquote><p></p>
[QUOTE="subzero, post: 7257264, member: 600350"] NO. we know what you are running. YOur not the first person to use a four channel amp that way. You will wire it up and get 2 chanels @ 100watts rms at 4 ohms. and that is probly going to be even less according to the volume levels When you bridge the rear channel you will only get 250watts rms @ 4 ohms. and that will probly be less as well. And it will definately be less than your recomended 600watts rms for that subs. (I assume you only have one sub?)(I hope) If you bridge that amp and run it at 2 ohms it might get hot and shut down. With a dual 4 ohm sub, the only wiring options you have are 8 ohms and 2 ohms and that amp doesnt say it is 2 ohm stable in a mono bridge.. So, what I suggest is that you go buy a better amp for your sub. sub specs Sensitivity: 84 dB RMS Power Range : 600 Watts Peak Power Handling: 1200 Watts Impedance: Dual 4 Ohm Low Frequency response: 30 Hz High Frequency Response: 400 Hz Diameter: 12 Inch amp specs Gothic Series 4-Channel Car Amplifier RMS Power Rating: [COLOR=red]4 ohms: 100 watts x 4 chan. [/COLOR] [COLOR=red]2 ohms: 125 watts x 4 chan. [/COLOR] [COLOR=red]Bridged, 4 ohms: 250 watts x 2 chan. [/COLOR] [COLOR=red]Max power output: 1200 watts [/COLOR]MOSFET power supply Pulse width modulation circuitry Remote bass level input (remote level control sold separately) LED power indicators Bass Boost (0-18 dB bass boost at 45 Hz) Tri-Mode capable 4/3/2 channel operation 2 Ohm stereo, 4 ohm mono stable Preamp RCA outputs Low level inputs (200mV-8V) Variable high-pass filter (40-250 Hz, 12 dB/octave) Variable low-pass filter (40-250 Hz, 12 dB/octave) Frequency response: 10-30,000 Hz [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Amplifiers
power acoustik amp HELP
Top
Menu
What's new
Forum list
