Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
New sub and amp issue
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="PWNED" data-source="post: 5646502" data-attributes="member: 583450"><p>For the Deck i have an Alpine 9884. For the amp i have a Kenwood KAC-9104D rated at 500rms at 4ohms/900rms at 2ohms. THe sub is a 10inch Kenwood KFC-W2511 rated at 300rms. At 2ohms thats good enough for an Alpine type R and if it doesnt push a kenwood then something is wrong. Dont get me wrong the kenwood hits pretty hard its just maxed out.</p><p></p><p>The amp is set at 80 for low pass freq/bass boost at 0/and the input sensitivity maxed all the way/ISF off/Phase set at 0. I have my deck set at 15 which is the max for subwoofer level and my bass at 2. The sub should of been blown by now putting up the input that high. I was going to turn up the input just before it distored but i cant get it to distort what so ever. My radio has 2v pre amps. If i were to have 4v pre amps would it be that much of a differance?</p><p></p><p><a href="http://www.sonicelectronix.com/item_11795_Kenwood+KAC-9104D.html" target="_blank">http://www.sonicelectronix.com/item_11795_Kenwood+KAC-9104D.html</a></p></blockquote><p></p>
[QUOTE="PWNED, post: 5646502, member: 583450"] For the Deck i have an Alpine 9884. For the amp i have a Kenwood KAC-9104D rated at 500rms at 4ohms/900rms at 2ohms. THe sub is a 10inch Kenwood KFC-W2511 rated at 300rms. At 2ohms thats good enough for an Alpine type R and if it doesnt push a kenwood then something is wrong. Dont get me wrong the kenwood hits pretty hard its just maxed out. The amp is set at 80 for low pass freq/bass boost at 0/and the input sensitivity maxed all the way/ISF off/Phase set at 0. I have my deck set at 15 which is the max for subwoofer level and my bass at 2. The sub should of been blown by now putting up the input that high. I was going to turn up the input just before it distored but i cant get it to distort what so ever. My radio has 2v pre amps. If i were to have 4v pre amps would it be that much of a differance? [URL="http://www.sonicelectronix.com/item_11795_Kenwood+KAC-9104D.html"]http://www.sonicelectronix.com/item_11795_Kenwood+KAC-9104D.html[/URL] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
New sub and amp issue
Top
Menu
What's new
Forum list