Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
New amp not working
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="crash9201" data-source="post: 5681246" data-attributes="member: 607369"><p>i just bought a power acoustiks 1200db mono, to power my two 10l74ohm, i upgraded my power and ground wire to 4 guage instead of 8 and hooked up the subs according to the top diagram here <a href="http://www.mp3car.com/vbulletin/attachments/car-audio/49102d1208280433-wiring-two-dual-voice-coil-subs-one-mono-amp-snap.gif." target="_blank">http://www.mp3car.com/vbulletin/attachments/car-audio/49102d1208280433-wiring-two-dual-voice-coil-subs-one-mono-amp-snap.gif.</a> i know there are various different ways of wiring these up i know it verywell could just be that the imp is to high but i wanna double check b4 i go thru the proccess of pulling the subs out and wiring them a different.</p><p></p><p>the amp turns on, the subs tap when the volume is REALLY low, like at 5, but if i go anyhigher they stop hitting but the amp doesnt go into protect, it stays on and should be fine.</p><p></p><p>my electrical is all stock, it should still make the subs pound, or so i thought</p><p></p><p>EDIT</p><p></p><p>I just realized that i had bought an unbridgable mono amp and hooked up 2 subs to it.... any otherway i can wire these</p></blockquote><p></p>
[QUOTE="crash9201, post: 5681246, member: 607369"] i just bought a power acoustiks 1200db mono, to power my two 10l74ohm, i upgraded my power and ground wire to 4 guage instead of 8 and hooked up the subs according to the top diagram here [URL="http://www.mp3car.com/vbulletin/attachments/car-audio/49102d1208280433-wiring-two-dual-voice-coil-subs-one-mono-amp-snap.gif."]http://www.mp3car.com/vbulletin/attachments/car-audio/49102d1208280433-wiring-two-dual-voice-coil-subs-one-mono-amp-snap.gif.[/URL] i know there are various different ways of wiring these up i know it verywell could just be that the imp is to high but i wanna double check b4 i go thru the proccess of pulling the subs out and wiring them a different. the amp turns on, the subs tap when the volume is REALLY low, like at 5, but if i go anyhigher they stop hitting but the amp doesnt go into protect, it stays on and should be fine. my electrical is all stock, it should still make the subs pound, or so i thought EDIT I just realized that i had bought an unbridgable mono amp and hooked up 2 subs to it.... any otherway i can wire these [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
New amp not working
Top
Menu
Home
Refresh