Reply to thread

Message

<blockquote data-quote="stefan.416" data-source="post: 3405328" data-attributes="member: 581273">hey everyone i have a audiobahn 4002T 2 ch amplifier i just bought a pioneer TS-W257D4 10&quot; sub because it was on sale. i was wondering wat would be the best way to set this up. the specs for the amp and sub are below:AMPLIFIER* Amplifier Class AB* Number of Channels 2* RMS Power (4 ohms) 100 watts x 2 channels* RMS Power (2 ohms) 200 watts x 2 channels* RMS Power (1 ohm) N/A* Bridged RMS Power 400 watts x 1 channel* Peak Power Output 800 watts x 1 channel* Minimum Impedance Unbridged 2 ohms* Minimum Impedance Bridged 4 ohms* THD at Rated RMS Power 0.02%* Speaker Level Inputs Yes* Preamp Outputs Yes - 1 pair* Built-in Crossover High-pass (HP), Low-pass (LP), Full (AP)* High-Pass Crossover Frequency 50 - 750 Hz* Low-Pass Crossover Frequency 50 - 120 Hz* Subsonic Filter 20 - 50 Hz* Signal-to-Noise Ratio 100 dB* Channel Separation N/A* Bass Boost On/Off Switch (0 or +18dB)SUBWOOFERBasket Material:&nbsp; &nbsp; &nbsp;&nbsp; SteelBinding Posts:&nbsp; &nbsp;&nbsp; Integrated Single Sided SilverCone Material:&nbsp; &nbsp;&nbsp; Composite IMPP, Interlaced Aramid FibreFrequency Response:&nbsp; &nbsp;&nbsp; 18 - 600HzImpedance:&nbsp; &nbsp;&nbsp; Dual 4 OhmsMagnet Weight:&nbsp; &nbsp;&nbsp; 74 Oz.Mounting Depth;&nbsp; &nbsp;&nbsp; 5.63&quot;Power Handling Max:&nbsp; &nbsp;&nbsp; 1000 WattsPower Handling Nominal:&nbsp; &nbsp;&nbsp; 350 Watts RMSSensitivity:&nbsp; &nbsp;&nbsp; 87dBSurround Material:&nbsp; &nbsp;&nbsp; FibreVoice Coil Size&nbsp; &nbsp;&nbsp; 2&quot;Woofer Size&nbsp; &nbsp;&nbsp; 10&quot;each voice coil terminal is rated at 4 ohmsso can someone please tell me how i should be setting this up. thanks</blockquote>

[QUOTE="stefan.416, post: 3405328, member: 581273"] hey everyone i have a audiobahn 4002T 2 ch amplifier i just bought a pioneer TS-W257D4 10" sub because it was on sale. i was wondering wat would be the best way to set this up. the specs for the amp and sub are below: AMPLIFIER * Amplifier Class AB * Number of Channels 2 * RMS Power (4 ohms) 100 watts x 2 channels * RMS Power (2 ohms) 200 watts x 2 channels * RMS Power (1 ohm) N/A * Bridged RMS Power 400 watts x 1 channel * Peak Power Output 800 watts x 1 channel * Minimum Impedance Unbridged 2 ohms * Minimum Impedance Bridged 4 ohms * THD at Rated RMS Power 0.02% * Speaker Level Inputs Yes * Preamp Outputs Yes - 1 pair * Built-in Crossover High-pass (HP), Low-pass (LP), Full (AP) * High-Pass Crossover Frequency 50 - 750 Hz * Low-Pass Crossover Frequency 50 - 120 Hz * Subsonic Filter 20 - 50 Hz * Signal-to-Noise Ratio 100 dB * Channel Separation N/A * Bass Boost On/Off Switch (0 or +18dB) SUBWOOFER Basket Material: Steel Binding Posts: Integrated Single Sided Silver Cone Material: Composite IMPP, Interlaced Aramid Fibre Frequency Response: 18 - 600Hz Impedance: Dual 4 Ohms Magnet Weight: 74 Oz. Mounting Depth; 5.63" Power Handling Max: 1000 Watts Power Handling Nominal: 350 Watts RMS Sensitivity: 87dB Surround Material: Fibre Voice Coil Size 2" Woofer Size 10" each voice coil terminal is rated at 4 ohms so can someone please tell me how i should be setting this up. thanks [/QUOTE]

Verification