Reply to thread

Message

<blockquote data-quote="Antics" data-source="post: 3718155" data-attributes="member: 584067">Need to know if this set up would work so I can start buying it //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gifKicker ZX650.4 :* 4-Channel ZX-Series Power Amplifier* Low Impedance Operation* SORT Protection Circuitry (Short circuit, Over-voltage, Reverse polarity, Thermal)* MOSFET Power Supply* KickBass: 0-18 dB @ 40 Hz* Built-In Variable Crossover: 12 dB High or Low-Pass operation (50-200 Hz)* High &amp;amp; Low level inputs* Custom tooled gold plated connectors* SAMS (Stereo And Mono Simultaneously) bridged mono load and a stereo load at the same time* Cast aluminum EndKaps* RMS Power Ratings:* 120 watts x 4 chan. @ 4 ohms* 170 watts x 4 chan. @ 2 ohms* 325 watts x 2 chan. @ 4 ohms Bridged* Input gain control: Low Level (125mV - 5V), High Level (250mV - 10V)PG RSD 65CS:*Power Handling: 60W/120W (RMS/Peak)*Impedance: 4 Ohms*Frequency Response: 45Hz - 20kHz*Sensitivity: 88dBsingle Kicker S10L7*Dual Voice Coil*Impedance 2 ohms*Peak Power Handling 1200&nbsp; watts*RMS Power Handling 600&nbsp; watts*Sensitivity 86.1&nbsp; dBI want to bridge 2 of the channels on the amp for the sub at 4 Ohms and use the other 2 channels for the RSD&#039;s I just want to know if this is possible and would it work correctly? I&#039;m still new so I also wanted to know since the Sub says &quot;Impedance 2 ohms&quot; will I still be able to wire it up to 4 ohms to the amp with no problems?thanks</blockquote>

[QUOTE="Antics, post: 3718155, member: 584067"] Need to know if this set up would work so I can start buying it [IMG]//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif[/IMG] [B]Kicker ZX650.4[/B] : * 4-Channel ZX-Series Power Amplifier * Low Impedance Operation * SORT Protection Circuitry (Short circuit, Over-voltage, Reverse polarity, Thermal) * MOSFET Power Supply * KickBass: 0-18 dB @ 40 Hz * Built-In Variable Crossover: 12 dB High or Low-Pass operation (50-200 Hz) * High & Low level inputs * Custom tooled gold plated connectors * SAMS (Stereo And Mono Simultaneously) bridged mono load and a stereo load at the same time * Cast aluminum EndKaps * RMS Power Ratings: * 120 watts x 4 chan. @ 4 ohms * 170 watts x 4 chan. @ 2 ohms * 325 watts x 2 chan. @ 4 ohms Bridged * Input gain control: Low Level (125mV - 5V), High Level (250mV - 10V) [B]PG RSD 65CS:[/B] *Power Handling: 60W/120W (RMS/Peak) *Impedance: 4 Ohms *Frequency Response: 45Hz - 20kHz *Sensitivity: 88dB [B]single Kicker S10L7[/B] *Dual Voice Coil *Impedance 2 ohms *Peak Power Handling 1200 watts *RMS Power Handling 600 watts *Sensitivity 86.1 dB I want to bridge 2 of the channels on the amp for the sub at 4 Ohms and use the other 2 channels for the RSD's I just want to know if this is possible and would it work correctly? I'm still new so I also wanted to know since the Sub says "Impedance 2 ohms" will I still be able to wire it up to 4 ohms to the amp with no problems? thanks [/QUOTE]

Verification