Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
Need good box designer
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Boomin_tahoe" data-source="post: 6209201" data-attributes="member: 562180"><p>This is the recommended ported box from Parts Express</p><p></p><p>Box Properties</p><p></p><p>--Description--</p><p></p><p>Name:</p><p></p><p>Type: Vented Box</p><p></p><p>Shape: Prism, square (optimum)</p><p></p><p>--Box Parameters--</p><p></p><p>Vb = 1.489 cu.ft</p><p></p><p>V(total) = 1.601 cu.ft</p><p></p><p>Fb = 21.16 Hz</p><p></p><p>QL = 6.885</p><p></p><p>F3 = 27.09 Hz</p><p></p><p>Fill = normal</p><p></p><p>--Vents--</p><p></p><p>No. of Vents = 1</p><p></p><p>Vent shape = round</p><p></p><p>Vent ends = one flush</p><p></p><p>Dv = 2.5 in</p><p></p><p>Lv = 17.38 in</p><p></p><p>Driver Properties</p><p></p><p>--Description--</p><p></p><p>Name:</p><p></p><p>Type: Standard one-way driver</p><p></p><p>--Configuration--</p><p></p><p>No. of Drivers = 1</p><p></p><p>--Mechanical Parameters--</p><p></p><p>Fs = 22 Hz</p><p></p><p>Qms = 2.8</p><p></p><p>Vas = 2.12 cu.ft</p><p></p><p>Cms = 0.12 in/lb</p><p></p><p>Mms = 2.692 oz</p><p></p><p>Rms = 8.307 lb/s</p><p></p><p>Xmax = 11 mm</p><p></p><p>Xmech = 22 mm</p><p></p><p>P-Dia = 7 in</p><p></p><p>Sd = 24829 sq.mm</p><p></p><p>P-Vd = 0.000273 cu.m</p><p></p><p>--Electrical Parameters--</p><p></p><p>Qes = 0.45</p><p></p><p>Re = 3.333 ohms</p><p></p><p>Z = 4 ohms</p><p></p><p>BL = 1.987 lb/A</p><p></p><p>--Electromech. Parameters--</p><p></p><p>Qts = 0.39</p><p></p><p>no = 0.137 %</p><p></p><p>1-W SPL = 83.51 dB</p><p></p><p>2.83-V SPL = 87.32 dB</p><p></p><p>I'm looking for a square vented box...with the vent under sub or on side next to the sub on same plane and the plate amp in back 180 degrees....front of box where sub is we'll call it 0 degrees. The subs rms wattage is 280...the amp will push out 240...should push it nicely. LMK if u need anything else.</p></blockquote><p></p>
[QUOTE="Boomin_tahoe, post: 6209201, member: 562180"] This is the recommended ported box from Parts Express Box Properties --Description-- Name: Type: Vented Box Shape: Prism, square (optimum) --Box Parameters-- Vb = 1.489 cu.ft V(total) = 1.601 cu.ft Fb = 21.16 Hz QL = 6.885 F3 = 27.09 Hz Fill = normal --Vents-- No. of Vents = 1 Vent shape = round Vent ends = one flush Dv = 2.5 in Lv = 17.38 in Driver Properties --Description-- Name: Type: Standard one-way driver --Configuration-- No. of Drivers = 1 --Mechanical Parameters-- Fs = 22 Hz Qms = 2.8 Vas = 2.12 cu.ft Cms = 0.12 in/lb Mms = 2.692 oz Rms = 8.307 lb/s Xmax = 11 mm Xmech = 22 mm P-Dia = 7 in Sd = 24829 sq.mm P-Vd = 0.000273 cu.m --Electrical Parameters-- Qes = 0.45 Re = 3.333 ohms Z = 4 ohms BL = 1.987 lb/A --Electromech. Parameters-- Qts = 0.39 no = 0.137 % 1-W SPL = 83.51 dB 2.83-V SPL = 87.32 dB I'm looking for a square vented box...with the vent under sub or on side next to the sub on same plane and the plate amp in back 180 degrees....front of box where sub is we'll call it 0 degrees. The subs rms wattage is 280...the amp will push out 240...should push it nicely. LMK if u need anything else. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
Need good box designer
Top
Menu
What's new
Forum list
