Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
My First Car Audio Setup!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="DukeNut" data-source="post: 7216156" data-attributes="member: 604611"><p>Depending on what rcas your alpine hu has, you will run 1 pair (front left and front right) to your 300/2 amp and if the hu has rear/subwoofer rcas, run another pair from the those to the 500/1. If the hu doesn't support more than 1 set of rcas, run them to the 300/2 and then use the 300/2 output rcas to run a pair to the 500/1. You can daisy chain the amp turn on wire also.</p><p></p><p>Run 2 speaker wires from 300/2 front left (1+ and 1-) to your left sides component xover input and 2 wires for the front right to right xover input. Run wire from xover out woofer to the woofer and same for the tweeter.</p><p></p><p>Run 2 speaker wires from 500/1 to sub.</p><p></p><p>Be sure to put appropriate sized fuse on your power wire within 18 inches of the battery. Also run rcas on opposite side of car than your power wire to help eliminate electrical noise. Use amp ground wires that are same size as power wire.</p><p></p><p>I didn't see anything indicating that you are running rear speakers, so i assume we don't need to address that.</p></blockquote><p></p>
[QUOTE="DukeNut, post: 7216156, member: 604611"] Depending on what rcas your alpine hu has, you will run 1 pair (front left and front right) to your 300/2 amp and if the hu has rear/subwoofer rcas, run another pair from the those to the 500/1. If the hu doesn't support more than 1 set of rcas, run them to the 300/2 and then use the 300/2 output rcas to run a pair to the 500/1. You can daisy chain the amp turn on wire also. Run 2 speaker wires from 300/2 front left (1+ and 1-) to your left sides component xover input and 2 wires for the front right to right xover input. Run wire from xover out woofer to the woofer and same for the tweeter. Run 2 speaker wires from 500/1 to sub. Be sure to put appropriate sized fuse on your power wire within 18 inches of the battery. Also run rcas on opposite side of car than your power wire to help eliminate electrical noise. Use amp ground wires that are same size as power wire. I didn't see anything indicating that you are running rear speakers, so i assume we don't need to address that. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
My First Car Audio Setup!
Top
Menu
What's new
Forum list