Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
Amplifiers
More Power out of my Kenwood?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="squeak9798" data-source="post: 719453" data-attributes="member: 555320"><p>Well, technically you can. <strong>However</strong>, the resistor will just waste that "extra" 200w the amp is now putting out as heat, and the sub will still only receive about 200w (just the same as it is now).</p><p></p><p></p><p>Well, first, you'd want to make <em>less</em> resistance to get more out of the amp //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif</p><p></p><p>But, regardless......</p><p></p><p>Stinger and Veritas made a device called the "Accumatch", which was supposed to have done just that, decrease the impedence and didn't just waste the extra power as heat, allowing the sub/speaker to receive more power. I beleive it was back in '95 that they got big......and it died that same year because the Accumatch was doing as much harm as it was good, and the program was for the most part discontinued (atleast by Stinger). Every once in a while they still pop up on egay though.</p><p></p><p>About the best thing you could do is sell your current sub (if it is the single 4ohm VC kind) and purchase either that same sub in the DVC 4ohm/coil flavor, or buy a different sub that would allow for a lower impedence.</p></blockquote><p></p>
[QUOTE="squeak9798, post: 719453, member: 555320"] Well, technically you can. [B]However[/B], the resistor will just waste that "extra" 200w the amp is now putting out as heat, and the sub will still only receive about 200w (just the same as it is now). Well, first, you'd want to make [I]less[/I] resistance to get more out of the amp [IMG]//content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif[/IMG] But, regardless...... Stinger and Veritas made a device called the "Accumatch", which was supposed to have done just that, decrease the impedence and didn't just waste the extra power as heat, allowing the sub/speaker to receive more power. I beleive it was back in '95 that they got big......and it died that same year because the Accumatch was doing as much harm as it was good, and the program was for the most part discontinued (atleast by Stinger). Every once in a while they still pop up on egay though. About the best thing you could do is sell your current sub (if it is the single 4ohm VC kind) and purchase either that same sub in the DVC 4ohm/coil flavor, or buy a different sub that would allow for a lower impedence. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Amplifiers
More Power out of my Kenwood?
Top
Menu
What's new
Forum list