Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Speakers
JL vs Morel vs Tangband
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="BLD 25" data-source="post: 2797947" data-attributes="member: 563837"><p>Hey, i am going active, and i am pretty set on the mids that i am going to use:</p><p></p><p><a href="http://www.partsexpress.com/pe/pshowdetl.cfm?&amp;DID=7&amp;Partnumber=295-335&amp;scqty=2" target="_blank">http://www.partsexpress.com/pe/pshowdetl.cfm?&amp;DID=7&amp;Partnumber=295-335&amp;scqty=2</a></p><p></p><p>I have read good reviews on them, and they are apparently very good even compared to the reference series, except they are 8 ohm. They begin to break up around 2k.</p><p></p><p>I am trying to decide on tweets.</p><p></p><p>I have a pair of JL XR tweets, but my concern are that they are aluminum, and they have a high crossover point --4000hz.</p><p></p><p>Other two that i am looking at are:</p><p></p><p>1) Low end morels:</p><p></p><p><a href="http://www.partsexpress.com/pe/showdetl.cfm?&amp;Partnumber=277-060" target="_blank">http://www.partsexpress.com/pe/showdetl.cfm?&amp;Partnumber=277-060</a></p><p></p><p>2)higher end tang band:</p><p></p><p><a href="http://www.partsexpress.com/pe/showdetl.cfm?&amp;Partnumber=264-822" target="_blank">http://www.partsexpress.com/pe/showdetl.cfm?&amp;Partnumber=264-822</a></p><p></p><p>both of these tweets have a much lower FS and xover point. Both can be crossed over at around 2k, and both are silk, which i think is more that i am looking for. I just know that JL is the big name and that is what people like, so i wanted some opinions. I could probably sell the JL's if i didn't use them.</p><p></p><p>The crossover i will be using is a DHD ntx-6211</p><p></p><p><a href="http://www.dhdusa.com/f_cross.html" target="_blank">http://www.dhdusa.com/f_cross.html</a></p></blockquote><p></p>
[QUOTE="BLD 25, post: 2797947, member: 563837"] Hey, i am going active, and i am pretty set on the mids that i am going to use: [URL="http://www.partsexpress.com/pe/pshowdetl.cfm?&DID=7&Partnumber=295-335&scqty=2"]http://www.partsexpress.com/pe/pshowdetl.cfm?&DID=7&Partnumber=295-335&scqty=2[/URL] I have read good reviews on them, and they are apparently very good even compared to the reference series, except they are 8 ohm. They begin to break up around 2k. I am trying to decide on tweets. I have a pair of JL XR tweets, but my concern are that they are aluminum, and they have a high crossover point --4000hz. Other two that i am looking at are: 1) Low end morels: [URL="http://www.partsexpress.com/pe/showdetl.cfm?&Partnumber=277-060"]http://www.partsexpress.com/pe/showdetl.cfm?&Partnumber=277-060[/URL] 2)higher end tang band: [URL="http://www.partsexpress.com/pe/showdetl.cfm?&Partnumber=264-822"]http://www.partsexpress.com/pe/showdetl.cfm?&Partnumber=264-822[/URL] both of these tweets have a much lower FS and xover point. Both can be crossed over at around 2k, and both are silk, which i think is more that i am looking for. I just know that JL is the big name and that is what people like, so i wanted some opinions. I could probably sell the JL's if i didn't use them. The crossover i will be using is a DHD ntx-6211 [URL="http://www.dhdusa.com/f_cross.html"]http://www.dhdusa.com/f_cross.html[/URL] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Speakers
JL vs Morel vs Tangband
Top
Menu
Home
Refresh