Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
Speakers
Is this distortion?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="jsloan10" data-source="post: 942842" data-attributes="member: 560397"><p>Heres a more comprehensive answer</p><p></p><p>5.21 What's worse for a speaker, too much or too little power? [iDB]</p><p></p><p>======================================================================</p><p></p><p>Problems occur (in everyday operation) when distortion is fed to a</p><p></p><p>speaker. This occurs MUCH more often when you are dealing with an</p><p></p><p>underpowered system - typically the owner will turn up the volume too</p><p></p><p>much or set the amplifier gains too high to try and get more volume</p><p></p><p>from the system. These introduce distortion to the signal - this will</p><p></p><p>destroy *any* speaker. ((see Section 5.22).)</p><p></p><p>When a speaker is overpowered, however, it is not nearly as common to</p><p></p><p>have these kind of problems, so speakers aren't blown as much. Of</p><p></p><p>course, it is certainly possible to destroy a speaker (thermally) by</p><p></p><p>overpowering it, but you'll have a pretty hard time doing this on your</p><p></p><p>own, especially with standard car audio amplifiers.</p><p></p><p>5.22 Why is distortion harmful to my speakers? [RK]</p><p></p><p>=====================================================</p><p></p><p>Distortion is hard on speakers for two reasons.</p><p></p><p>Reason 1: Distortion causes the power spectrum to shift upwards in</p><p></p><p>frequency. A bass note, when distorted, will have lots of high</p><p></p><p>frequency energy. This will cause mid-ranges and tweeters to fry, if</p><p></p><p>the amplifier is operating full range. It doesn't harm woofers,</p><p></p><p>necessarily.</p><p></p><p>Reason 2: Distortion causes the average power to be much higher.</p><p></p><p>Typically, a music signal that never clips has an average power level of</p><p></p><p>1/4 the peak power level for even the most compressed speed metal or</p><p></p><p>pop. More dynamic music will be 1/8 the peak level or less on average.</p><p></p><p>When you clip the amp hard, the average output moves up to the</p><p></p><p>full-rated output of the amp or more. The peak to average ratio can be</p><p></p><p>less than 2 to 1, with the peaks being at double the rated power of the</p><p></p><p>amp, and the average being at the rated power of the amp or higher.</p><p></p><p>Thermally, the speaker can handle the average power being 1/4 the rated</p><p></p><p>power of the amp (little to no clipping), but it will have a much harder</p><p></p><p>time with the average power being the amp's rated power or more (massive</p><p></p><p>clipping). As you might expect, this is pretty hard on the amp, too.</p><p></p><p>For transients, most speakers can handle a ton of power. But for long</p><p></p><p>term signals, the power handling is much less.</p></blockquote><p></p>
[QUOTE="jsloan10, post: 942842, member: 560397"] Heres a more comprehensive answer 5.21 What's worse for a speaker, too much or too little power? [iDB] ====================================================================== Problems occur (in everyday operation) when distortion is fed to a speaker. This occurs MUCH more often when you are dealing with an underpowered system - typically the owner will turn up the volume too much or set the amplifier gains too high to try and get more volume from the system. These introduce distortion to the signal - this will destroy *any* speaker. ((see Section 5.22).) When a speaker is overpowered, however, it is not nearly as common to have these kind of problems, so speakers aren't blown as much. Of course, it is certainly possible to destroy a speaker (thermally) by overpowering it, but you'll have a pretty hard time doing this on your own, especially with standard car audio amplifiers. 5.22 Why is distortion harmful to my speakers? [RK] ===================================================== Distortion is hard on speakers for two reasons. Reason 1: Distortion causes the power spectrum to shift upwards in frequency. A bass note, when distorted, will have lots of high frequency energy. This will cause mid-ranges and tweeters to fry, if the amplifier is operating full range. It doesn't harm woofers, necessarily. Reason 2: Distortion causes the average power to be much higher. Typically, a music signal that never clips has an average power level of 1/4 the peak power level for even the most compressed speed metal or pop. More dynamic music will be 1/8 the peak level or less on average. When you clip the amp hard, the average output moves up to the full-rated output of the amp or more. The peak to average ratio can be less than 2 to 1, with the peaks being at double the rated power of the amp, and the average being at the rated power of the amp or higher. Thermally, the speaker can handle the average power being 1/4 the rated power of the amp (little to no clipping), but it will have a much harder time with the average power being the amp's rated power or more (massive clipping). As you might expect, this is pretty hard on the amp, too. For transients, most speakers can handle a ton of power. But for long term signals, the power handling is much less. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Speakers
Is this distortion?
Top
Menu
What's new
Forum list
