Reply to thread

Message

<blockquote data-quote="rival904" data-source="post: 6680996" data-attributes="member: 610200">The guy who designed Desires box, is the same guy who designed this box, and is the same guy that DD goes through for ALL of their demo vehicles.I think HE would know the best, if anyone on what these subs should do in this setup, also, a smaller sealed/porter chamber will allow me to run more power, considering I will be running twice the RMS power to these subs, power handling was important.Heres what he said when I asked him about the small sealed/ported ratio and the small cu.in of port&quot;Dude, I&#039;m getting so tired of this.&nbsp; It&#039;s not you, it&#039;s just the whole idea of me busting my *** as hard as I do with all the R&amp;amp;D, the particle collision engine, resistive transfer theory, etc., only to be second-guessed by some kid that treats a complex cabin / enclosure model like a children&#039;s coloring book.&nbsp; I mean, sealed and ported volumes?&nbsp; I honestly thought you were just being cute by mimicking those challenged WinISD jockeys on CA.com.&nbsp; I&#039;d be interested to know how the person giving you advice is compensating for reactive cabin impedance acting on the port (or the effect that this has on the center chamber&#039;s equivalent air mass capacitance.)&nbsp; On the other hand, that&#039;s pointless; asking questions that you know someone isn&#039;t going to have the answers to is like quizzing a creationist on the theory of evolution--you&#039;re not proving anything and you **** sure aren&#039;t teaching them anything; it&#039;s like a special Olympics pissing match.&nbsp; All right...&nbsp; End of rant.&quot;And then he said&quot;It’s all good.&nbsp; We’ll let the box speak for itself once it’s built and playing.&nbsp; I’m just a bit *****y because I’ve been up for the past 48 hours.&nbsp; (That, and Thumper from the forum pulled the exact same shit a little while back when he got his design; came back talking about sealed and ported volumes adding up to something weird looking when modeled on a toy like WinISD, BassBox Pro, or some online box calculator…)&nbsp; Well anyway.&nbsp; I hope you like the way your setup sounds.&nbsp; Make ABSOLUTELY CERTAIN that you have no air leaks.&nbsp; And, if you’d like, you can put in additional bracing in the center chamber (iron rods, 2x4s, etc…)&nbsp; Best of luck.&quot;Him and DD are obviously doing something right with their current track record.</blockquote>

[QUOTE="rival904, post: 6680996, member: 610200"] The guy who designed Desires box, is the same guy who designed this box, and is the same guy that DD goes through for ALL of their demo vehicles. I think HE would know the best, if anyone on what these subs should do in this setup, also, a smaller sealed/porter chamber will allow me to run more power, considering I will be running twice the RMS power to these subs, power handling was important. Heres what he said when I asked him about the small sealed/ported ratio and the small cu.in of port "Dude, I'm getting so tired of this. It's not you, it's just the whole idea of me busting my *** as hard as I do with all the R&D, the particle collision engine, resistive transfer theory, etc., only to be second-guessed by some kid that treats a complex cabin / enclosure model like a children's coloring book. I mean, sealed and ported volumes? I honestly thought you were just being cute by mimicking those challenged WinISD jockeys on CA.com. I'd be interested to know how the person giving you advice is compensating for reactive cabin impedance acting on the port (or the effect that this has on the center chamber's equivalent air mass capacitance.) On the other hand, that's pointless; asking questions that you know someone isn't going to have the answers to is like quizzing a creationist on the theory of evolution--you're not proving anything and you **** sure aren't teaching them anything; it's like a special Olympics pissing match. All right... End of rant." And then he said "It’s all good. We’ll let the box speak for itself once it’s built and playing. I’m just a bit *****y because I’ve been up for the past 48 hours. (That, and Thumper from the forum pulled the exact same shit a little while back when he got his design; came back talking about sealed and ported volumes adding up to something weird looking when modeled on a toy like WinISD, BassBox Pro, or some online box calculator…) Well anyway. I hope you like the way your setup sounds. Make ABSOLUTELY CERTAIN that you have no air leaks. And, if you’d like, you can put in additional bracing in the center chamber (iron rods, 2x4s, etc…) Best of luck." Him and DD are obviously doing something right with their current track record. [/QUOTE]

Verification