Reply to thread

Message

<blockquote data-quote="dredey" data-source="post: 5487944" data-attributes="member: 605079">so how can i bridge my 2 channel amp and get 2 ohms out of it with the type rsim guessing 2 ohms will give the most powerthe audioque 1200 d is stable to to 1 ohmso ican do that to right, without harming my amp or substhese are the specs..Sub&nbsp; AudioQue 1200DModel&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; AQ1200DFrequency Response&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; 20Hz—250HzSignal to Noise Ratio&nbsp; &nbsp; &nbsp;&nbsp; 100dbLow Pass Crossover&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 24db / OctLow Pass Crossover Range&nbsp; &nbsp;&nbsp; 20Hz—200HzSubsonic Crossover Range&nbsp; &nbsp;&nbsp; 10Hz—50HzInput Sensitivity&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 0.2V—8VOutput Master / Input Slave Connection&nbsp; &nbsp; &nbsp;&nbsp; YesWorking Voltage&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 8V---16VEfficiency @ 4 ohm&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; 84%Damping Factor&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; Less than 150Fuse Rating&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; 40Amp X 3 (Linked 240 Amp)Output Power 14.4V @ 1% THD&nbsp; &nbsp; &nbsp; 510X1 @ 4 ohm,870X1 @ 2 ohm,1200X1 @1 ohmOutput Power 14.4V @ 5% THD&nbsp; &nbsp; &nbsp; 1470X1 @ 1 ohmDash Mounted Remote&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; IncludedDimensions&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; 12.75&quot;(L)x9.27&quot;(W)x2.35&quot;(H)*&nbsp; AQ series amplifiers are fully stable down to one ohm.* Daisy Chain connection of two amplifiers stable down to 2 ohms* Four way protection circuits: Speaker shorts, DC offset, High/Low voltage, Thermal protection* Double sided boards with high current MOSFET switching devices* 24db/oct slope crossovers, Fully adjustable Low Pass Filter and Subsonic FilterSub&nbsp; Alpine Type R 450$# 12&quot; subwoofer with dual 4-ohm voice coils# Kevlar reinforced pulp cone with Santoprene™ rubber surround# cast aluminum frame with perimeter venting# frequency response: 25-500 Hz# power handling: 200-500 watts RMS (250 watts per coil)# peak power: 1,500 watts# sensitivity: 85 dB# top-mount depth: 7-5/8&quot;# sealed box volume: 0.57-1.0 cu. ft.# ported box volume: 0.75-2.0 cu. ft.</blockquote>

[QUOTE="dredey, post: 5487944, member: 605079"] so how can i bridge my 2 channel amp and get 2 ohms out of it with the type rs im guessing 2 ohms will give the most power the audioque 1200 d is stable to to 1 ohm so ican do that to right, without harming my amp or subs these are the specs.. Sub AudioQue 1200D Model AQ1200D Frequency Response 20Hz—250Hz Signal to Noise Ratio 100db Low Pass Crossover 24db / Oct Low Pass Crossover Range 20Hz—200Hz Subsonic Crossover Range 10Hz—50Hz Input Sensitivity 0.2V—8V Output Master / Input Slave Connection Yes Working Voltage 8V---16V Efficiency @ 4 ohm 84% Damping Factor Less than 150 Fuse Rating 40Amp X 3 (Linked 240 Amp) Output Power 14.4V @ 1% THD 510X1 @ 4 ohm, 870X1 @ 2 ohm, 1200X1 @1 ohm Output Power 14.4V @ 5% THD 1470X1 @ 1 ohm Dash Mounted Remote Included Dimensions 12.75"(L)x9.27"(W)x2.35"(H) * AQ series amplifiers are fully stable down to one ohm. * Daisy Chain connection of two amplifiers stable down to 2 ohms * Four way protection circuits: Speaker shorts, DC offset, High/Low voltage, Thermal protection * Double sided boards with high current MOSFET switching devices * 24db/oct slope crossovers, Fully adjustable Low Pass Filter and Subsonic Filter Sub Alpine Type R 450$ # 12" subwoofer with dual 4-ohm voice coils # Kevlar reinforced pulp cone with Santoprene™ rubber surround # cast aluminum frame with perimeter venting # frequency response: 25-500 Hz # power handling: 200-500 watts RMS (250 watts per coil) # peak power: 1,500 watts # sensitivity: 85 dB # top-mount depth: 7-5/8" # sealed box volume: 0.57-1.0 cu. ft. # ported box volume: 0.75-2.0 cu. ft. [/QUOTE]

Verification