Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
Help with simple design
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="MikeyF" data-source="post: 6548744" data-attributes="member: 611696"><p>Hey, I needed some help with a simple design. I was wondering if anyone could draw up a box design for a 12" DC LVL 4, tuned to 33hz. The website says it should be 1.5 cubes, but I defiantly thought they would be a bit bigger, like around 3. Would like it for a daily driver. But heres the info for the sub, and any help would be greatly appreciated. Thanks, Mike.</p><p></p><p>Mounting Depth</p><p></p><p>6.75"</p><p></p><p>Mounting Hole Diameter</p><p></p><p>11"</p><p></p><p>Motor Width</p><p></p><p>7.75"</p><p></p><p>VC Diameter</p><p></p><p>3"</p><p></p><p>Magnet Weight</p><p></p><p>28.5lbs</p><p></p><p>Sd</p><p></p><p>494.00 cm²</p><p></p><p>Vas</p><p></p><p>66.60 L</p><p></p><p>Cms</p><p></p><p>1.95e-04 m/N</p><p></p><p>Mms</p><p></p><p>173.08 g</p><p></p><p>Fs</p><p></p><p>27.4 Hz</p><p></p><p>Bl</p><p></p><p>16.15</p><p></p><p>Le</p><p></p><p>4.02 mH</p><p></p><p>Qms</p><p></p><p>5.13</p><p></p><p>Qes</p><p></p><p>0.42</p><p></p><p>Qts</p><p></p><p>0.39</p><p></p><p>Xmax</p><p></p><p>23.5 mm</p><p></p><p>Sensitivity</p><p></p><p>87.0 dB</p><p></p><p>Suggested Ported</p><p></p><p>1.5³ ft</p><p></p><p>Suggested SPL Ported</p><p></p><p>2³ ft</p></blockquote><p></p>
[QUOTE="MikeyF, post: 6548744, member: 611696"] Hey, I needed some help with a simple design. I was wondering if anyone could draw up a box design for a 12" DC LVL 4, tuned to 33hz. The website says it should be 1.5 cubes, but I defiantly thought they would be a bit bigger, like around 3. Would like it for a daily driver. But heres the info for the sub, and any help would be greatly appreciated. Thanks, Mike. Mounting Depth 6.75" Mounting Hole Diameter 11" Motor Width 7.75" VC Diameter 3" Magnet Weight 28.5lbs Sd 494.00 cm² Vas 66.60 L Cms 1.95e-04 m/N Mms 173.08 g Fs 27.4 Hz Bl 16.15 Le 4.02 mH Qms 5.13 Qes 0.42 Qts 0.39 Xmax 23.5 mm Sensitivity 87.0 dB Suggested Ported 1.5³ ft Suggested SPL Ported 2³ ft [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
Help with simple design
Top
Menu
Home
Refresh