Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Getting new R1200-1D Monoblock amp tomorrow, not sure how to safely pair ohms withsub
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Kadenj" data-source="post: 8363911" data-attributes="member: 665166"><p>Thanks a bunch n2audio, i appreciate you correcting any misleading information //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif</p><p></p><p>So i got the new amp this afternoon. I hooked it all up, except for the speakers, and tested voltage from the speaker terminals on the amplifier, but i simply Could Not Get a good reading. Now i'm not very familiar with the different settings on a DMM but i was on the 200 V setting (and YES I KNOW i should just go research that and not ask you guys for simple ****) So i don't exactly know that i was doing it correctly but i digress. I couldn't set the gain using the dmm, so i set it by ear, and im pleased with it, but i really want to make sure it's Safe, and if there is a way to make everything sound more CLEAR (Which right now it's sounds very clear, but i'm just not sure it's at it's clearest) i really want to know how to do it properly. There are a few knobs that i don't completely understand as well. The Punch EQ (Which is associated with the knob i don't have connected yet) THen there is an Infrasonic filter hz knob, from 15-40hz, then another filter i think from 50-200 hz. Where should i set THESE knobs, because i feel like when i move them around i'm losing certain ranges, and i'm just not sure how to know where to put them to get the max range and max quality. Sorry if this is a little much to ask haha //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif</p></blockquote><p></p>
[QUOTE="Kadenj, post: 8363911, member: 665166"] Thanks a bunch n2audio, i appreciate you correcting any misleading information [IMG]//content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif[/IMG] So i got the new amp this afternoon. I hooked it all up, except for the speakers, and tested voltage from the speaker terminals on the amplifier, but i simply Could Not Get a good reading. Now i'm not very familiar with the different settings on a DMM but i was on the 200 V setting (and YES I KNOW i should just go research that and not ask you guys for simple ****) So i don't exactly know that i was doing it correctly but i digress. I couldn't set the gain using the dmm, so i set it by ear, and im pleased with it, but i really want to make sure it's Safe, and if there is a way to make everything sound more CLEAR (Which right now it's sounds very clear, but i'm just not sure it's at it's clearest) i really want to know how to do it properly. There are a few knobs that i don't completely understand as well. The Punch EQ (Which is associated with the knob i don't have connected yet) THen there is an Infrasonic filter hz knob, from 15-40hz, then another filter i think from 50-200 hz. Where should i set THESE knobs, because i feel like when i move them around i'm losing certain ranges, and i'm just not sure how to know where to put them to get the max range and max quality. Sorry if this is a little much to ask haha [IMG]//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif[/IMG] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Getting new R1200-1D Monoblock amp tomorrow, not sure how to safely pair ohms withsub
Top
Menu
Home
Refresh