Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
First time building my own enclosure
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="JustinStone" data-source="post: 8751640" data-attributes="member: 680824"><p>Two skar SVR-12's running off 550watts rms @ 2ohms from a MA1889i amp. Box is 3.70-3.75ft³ net, and tuned to 34hz. Should be readily available for 800watts rms. Placed in the trunk of a Pt Cruiser; facing deck-lid.</p><p></p><p>I'm pretty proud of it, tbh...</p><p></p><p><img src="https://www.caraudio.com/attachments/0001-jpg.26617/" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p></p><p>AutoCAD drawing (ended up only using 1" threaded rods)</p><p></p><p>[ATTACH=full]30070[/ATTACH]</p><p></p><p>All pieces cut out, but the L ruler I was using turn out to be bent.. had to do a lot of measurements again and almost every cut was jagged from using a hand-held circular saw. This part demotivated me the most since everything wasn't lining up properly.</p><p></p><p>[ATTACH=full]30071[/ATTACH]</p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p>I shaved a lot of sides flat; decided to push through my disappointment, and begin fitting the pieces together.</p><p></p><p>[ATTACH=full]30072[/ATTACH]</p><p></p><p>I ended up using A LOT of wood glue and caulk, and the weight is almost too much for me to carry alone.</p><p></p><p>[ATTACH=full]30073[/ATTACH]</p><p></p><p>All in all, its pretty rough.. but I gotta start somewhere or I'll never leave the starting block.</p><p></p><p>[ATTACH=full]30074[/ATTACH]</p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p></p><p>She hits pretty low though: flexes the trunk, roof/sunroof, and doors pretty hard at 20-25hz. Have yet to get an SPL reading, but I want to wait until 800watts to do so.</p></blockquote><p></p>
[QUOTE="JustinStone, post: 8751640, member: 680824"] Two skar SVR-12's running off 550watts rms @ 2ohms from a MA1889i amp. Box is 3.70-3.75ft³ net, and tuned to 34hz. Should be readily available for 800watts rms. Placed in the trunk of a Pt Cruiser; facing deck-lid. I'm pretty proud of it, tbh... [IMG]https://www.caraudio.com/attachments/0001-jpg.26617/[/IMG] AutoCAD drawing (ended up only using 1" threaded rods) [ATTACH type="full" width="553px" alt="30070"]30070[/ATTACH] All pieces cut out, but the L ruler I was using turn out to be bent.. had to do a lot of measurements again and almost every cut was jagged from using a hand-held circular saw. This part demotivated me the most since everything wasn't lining up properly. [ATTACH type="full" align="left"]30071[/ATTACH] I shaved a lot of sides flat; decided to push through my disappointment, and begin fitting the pieces together. [ATTACH type="full" width="276px" alt="30072"]30072[/ATTACH] I ended up using A LOT of wood glue and caulk, and the weight is almost too much for me to carry alone. [ATTACH type="full" width="281px" alt="30073"]30073[/ATTACH] All in all, its pretty rough.. but I gotta start somewhere or I'll never leave the starting block. [ATTACH type="full" align="left"]30074[/ATTACH] She hits pretty low though: flexes the trunk, roof/sunroof, and doors pretty hard at 20-25hz. Have yet to get an SPL reading, but I want to wait until 800watts to do so. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
First time building my own enclosure
Top
Menu
Home
Refresh