Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Builds
Car Audio Build Logs
First-Time Audio Build in Honda Accord Euro CU2. Full active setup help wanted
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="AndrewMelon2121" data-source="post: 8905987" data-attributes="member: 693922"><p>Hi everyone, look I might be making a fool of myself, but I wanted to give a crack at doing this audio system myself. Currently have an aftermarket subwoofer and Monoblock amp already installed and working, but I’m now upgrading the front stage with a 4-channel amp and DSP.</p><p></p><p>I am kinda confused about the wiring sizes and wanted to confirm if this electrical diagram setup is ok. Lucky for me I got the subwoofer installed professional so I can follow kinda get some pointers from it. I am also confused on what distribution blocks to get. Any feedback or advice would be much appreciated.</p><p></p><p><strong>My Planned Setup:</strong></p><p></p><p>Head Unit: Factory luxury Navi HU (staying stock)</p><p></p><p>DSP: Hertz H8 DSP</p><p></p><p>Monoblock AMP: Morel MPD 1.500 Monoblock AMP</p><p></p><p>Subwoofer: Hertz MP 300D4.3 12 subwoofer.</p><p></p><p>4 channel AMP: Pioneer GM-D8704 (for front components)</p><p></p><p>Front speakers: Planning to run full active with Hertz MPK 165.3 Pro front stage</p><p></p><p>Rear speakers: MPX 165.3 left on HU unit</p><p></p><p>Distribution block connected too battery via fused 4AWG ( not sure what size of wire to use)</p><p></p><p>Mini Fuse tap for ACC to turn on DSP</p><p></p><p></p><p></p><p><strong>Wiring Diagram:</strong></p><p></p><p>DSP Power Connected to fuse tap near glovebox.</p><p></p><p>DSP Ground: Shared grounding block with both amps, secured to bare chassis point.</p><p></p><p>Power for amps and DSP: From distribution block connected to battery</p><p></p><p>Remote Turn-On DSP REM OUT - both amps REM IN (split or daisy chained).</p><p></p><p>Speaker Input (high level): I’ll tap Front L+R speaker wires from stock amp at the boot and feed them into DSP HIGH INPUT harness.</p><p></p><p>RCA Outputs:</p><p></p><p>DSP CH1 & CH2 - 4ch Amp CH1 & CH2 (Tweeters)</p><p></p><p>DSP CH3 & CH4 - 4ch Amp CH3 & CH4 (Midbass)</p><p></p><p>DSP CH7 & CH8 - Monoblock Amp L+R RCA IN (Subwoofer)</p></blockquote><p></p>
[QUOTE="AndrewMelon2121, post: 8905987, member: 693922"] Hi everyone, look I might be making a fool of myself, but I wanted to give a crack at doing this audio system myself. Currently have an aftermarket subwoofer and Monoblock amp already installed and working, but I’m now upgrading the front stage with a 4-channel amp and DSP. I am kinda confused about the wiring sizes and wanted to confirm if this electrical diagram setup is ok. Lucky for me I got the subwoofer installed professional so I can follow kinda get some pointers from it. I am also confused on what distribution blocks to get. Any feedback or advice would be much appreciated. [B]My Planned Setup:[/B] Head Unit: Factory luxury Navi HU (staying stock) DSP: Hertz H8 DSP Monoblock AMP: Morel MPD 1.500 Monoblock AMP Subwoofer: Hertz MP 300D4.3 12 subwoofer. 4 channel AMP: Pioneer GM-D8704 (for front components) Front speakers: Planning to run full active with Hertz MPK 165.3 Pro front stage Rear speakers: MPX 165.3 left on HU unit Distribution block connected too battery via fused 4AWG ( not sure what size of wire to use) Mini Fuse tap for ACC to turn on DSP [B]Wiring Diagram:[/B] DSP Power Connected to fuse tap near glovebox. DSP Ground: Shared grounding block with both amps, secured to bare chassis point. Power for amps and DSP: From distribution block connected to battery Remote Turn-On DSP REM OUT - both amps REM IN (split or daisy chained). Speaker Input (high level): I’ll tap Front L+R speaker wires from stock amp at the boot and feed them into DSP HIGH INPUT harness. RCA Outputs: DSP CH1 & CH2 - 4ch Amp CH1 & CH2 (Tweeters) DSP CH3 & CH4 - 4ch Amp CH3 & CH4 (Midbass) DSP CH7 & CH8 - Monoblock Amp L+R RCA IN (Subwoofer) [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Builds
Car Audio Build Logs
First-Time Audio Build in Honda Accord Euro CU2. Full active setup help wanted
Top
Menu
What's new
Forum list
