Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
everything needed for 4 amps
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="96stratus" data-source="post: 6705427" data-attributes="member: 619910"><p>Well they are crunches here are the specs for thr 3 that are going to the 6 12s mind you these are powering 150 watt rms kickers 2 for each amp</p><p></p><p>Maximum power ratings of 2 x 125 watts @ 4 ohms, 2 x 250 watts @ 2 ohms, 1 x 500 @ 4 ohms</p><p></p><p>SEPP A/B class amplifier design</p><p></p><p>Bridgeable design</p><p></p><p>Rugged MOSFET pulse width modulation power supply</p><p></p><p>2-ohm capable A/B class 2-channel amp</p><p></p><p>System diagnostics (with LEDs) protect against current/amperage overload, short circuits, thermal overload and DC offset</p><p></p><p>High-level speaker lead inputs</p><p></p><p>Silver preamp-level RCA-type inputs</p><p></p><p>Daisy-chain line outputs</p><p></p><p>Oversized speaker terminals</p><p></p><p>Illuminated Crunch logo</p><p></p><p>and the other is a 4 channel autotek for the mids n highs</p><p></p><p>150 watts of maximum power x four channels into four ohms for a total of 600 watts of maximum power</p><p></p><p>300 watts of maximum power x four channels into two ohms for a total of 1200 watts of maximum power</p><p></p><p>600 watts of maximum bridged power x 2 channels into four ohms</p><p></p><p>Advanced MOSFET PWM power supply</p><p></p><p>Oversized speaker terminals</p><p></p><p>RCA-type preamp inputs</p><p></p><p>High-level inputs (speaker)</p><p></p><p>Daisy-chain line outputs</p><p></p><p>Mono/stereo switch</p><p></p><p>High-pass/low-pass frequency selections</p><p></p><p>Diagnostic LED power protection system to detect and warn of problems</p><p></p><p>ive ran 4 15s on a 1k mono amp with stock alt and batt with no problems this set up is roughly under 900 watts rms total power i plan to go bigger amp and 1 more battery</p></blockquote><p></p>
[QUOTE="96stratus, post: 6705427, member: 619910"] Well they are crunches here are the specs for thr 3 that are going to the 6 12s mind you these are powering 150 watt rms kickers 2 for each amp Maximum power ratings of 2 x 125 watts @ 4 ohms, 2 x 250 watts @ 2 ohms, 1 x 500 @ 4 ohms SEPP A/B class amplifier design Bridgeable design Rugged MOSFET pulse width modulation power supply 2-ohm capable A/B class 2-channel amp System diagnostics (with LEDs) protect against current/amperage overload, short circuits, thermal overload and DC offset High-level speaker lead inputs Silver preamp-level RCA-type inputs Daisy-chain line outputs Oversized speaker terminals Illuminated Crunch logo and the other is a 4 channel autotek for the mids n highs 150 watts of maximum power x four channels into four ohms for a total of 600 watts of maximum power 300 watts of maximum power x four channels into two ohms for a total of 1200 watts of maximum power 600 watts of maximum bridged power x 2 channels into four ohms Advanced MOSFET PWM power supply Oversized speaker terminals RCA-type preamp inputs High-level inputs (speaker) Daisy-chain line outputs Mono/stereo switch High-pass/low-pass frequency selections Diagnostic LED power protection system to detect and warn of problems ive ran 4 15s on a 1k mono amp with stock alt and batt with no problems this set up is roughly under 900 watts rms total power i plan to go bigger amp and 1 more battery [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
everything needed for 4 amps
Top
Menu
What's new
Forum list
