Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
Dual 10" front face slot port in making
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="MitchnSystem" data-source="post: 8864529" data-attributes="member: 690423"><p>Hello y'all! Good evening, hope everyone is well. Newbie here...to the whole posting aspect of the forum deal, that is. I apologize if I am doing anything wrong already...as in perhaps, posting n wrong location etc ...</p><p>But quick question. Im currently designing a dual 10" front face slot port labyrinth enclosure. I have been doing head spinning amounts of research pertaining to the actual design from dimensions to port size and volumes to bracing and available vol of vehicle cab <img class="smilie smilie--emoji" loading="lazy" alt="😵💫" title="😵💫" src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f635-1f4ab.png" /><img class="smilie smilie--emoji" loading="lazy" alt="😵💫" title="😵💫" src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f635-1f4ab.png" /><img class="smilie smilie--emoji" loading="lazy" alt="😵💫" title="😵💫" src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f635-1f4ab.png" />. Lol. Not that bad really.. just tend to get frustrating when you have hit that point where u r ending up back at the start of the information line. Ne ways.</p><p>My question, as simple and clear cut as I can word it is .... "how or where does one come up with the specs or dimensions pertaining strictly to sizing and placement of the inner walls of the enclosure which makes up the labyrinth?"</p><p>I can not find a formula or process of ne kind as far as to figure numbers on these walls. Tons on port size and tuning or formulas for volume along with bracing and everything else. But how do u know how long the inner wall that runs parallel with the port wall is supposed to be? Or at what point does it make it's turn into the inner box, making the wall that runs perpandicuar? At what angle...90°? How far does that wall go on? Should it span out, covering the center of the magnet or stop just short of doing so etc...? Any help or guidance will b greatly appreciated. Thanks in advance for your time and knowledge.</p><p><img class="smilie smilie--emoji" loading="lazy" alt="🙂" title="🙂" src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f642.png" /><img class="smilie smilie--emoji" loading="lazy" alt="👍🏼" title="👍🏼" src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f44d-1f3fc.png" /><img class="smilie smilie--emoji" loading="lazy" alt="🔊" title="🔊" src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f50a.png" /><img class="smilie smilie--emoji" loading="lazy" alt="🎶" title="🎶" src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f3b6.png" /><img class="smilie smilie--emoji" loading="lazy" alt="🎵" title="🎵" src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f3b5.png" /></p></blockquote><p></p>
[QUOTE="MitchnSystem, post: 8864529, member: 690423"] Hello y'all! Good evening, hope everyone is well. Newbie here...to the whole posting aspect of the forum deal, that is. I apologize if I am doing anything wrong already...as in perhaps, posting n wrong location etc ... But quick question. Im currently designing a dual 10" front face slot port labyrinth enclosure. I have been doing head spinning amounts of research pertaining to the actual design from dimensions to port size and volumes to bracing and available vol of vehicle cab 😵💫😵💫😵💫. Lol. Not that bad really.. just tend to get frustrating when you have hit that point where u r ending up back at the start of the information line. Ne ways. My question, as simple and clear cut as I can word it is .... "how or where does one come up with the specs or dimensions pertaining strictly to sizing and placement of the inner walls of the enclosure which makes up the labyrinth?" I can not find a formula or process of ne kind as far as to figure numbers on these walls. Tons on port size and tuning or formulas for volume along with bracing and everything else. But how do u know how long the inner wall that runs parallel with the port wall is supposed to be? Or at what point does it make it's turn into the inner box, making the wall that runs perpandicuar? At what angle...90°? How far does that wall go on? Should it span out, covering the center of the magnet or stop just short of doing so etc...? Any help or guidance will b greatly appreciated. Thanks in advance for your time and knowledge. 🙂👍🏼🔊🎶🎵 [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
Dual 10" front face slot port in making
Top
Menu
Home
Refresh