Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Amplifiers
does the amplifier divide power.......
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="mat3833" data-source="post: 7933305" data-attributes="member: 587645"><p>re-read my first post. i only used the "RMS" figure to help make my point. i stated you can wire the higher powered sub to a lower ohm load to receive more power and vice versa. you could wire the "lower RMS" sub to a lower load and blow it if u wanted to. and when i did something like this i had 4 subs total at the time. i had 2 6.5" subs in Tapped horns, 1 10" sub in a sealed box, and a 15" sub in a really low tuned ported box. basicly the 6.5s played midbass and down to ~90hz, the sealed 10 played~90hz to ~35hz, and the ported 15 played 35hz and below. the crossover network was a pain in the ***, but total system power was only ~1K watts and it sounded **** good.</p><p></p><p>and the phasing was basicly a non issue due to the crossover settup. there was some slight cancelation at each crossover point but a sinple EQ boost fixed that problem. <img src="data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7" class="smilie smilie--sprite smilie--sprite1" alt=":)" title="Smile :)" loading="lazy" data-shortname=":)" /></p><p></p><p>Matt</p></blockquote><p></p>
[QUOTE="mat3833, post: 7933305, member: 587645"] re-read my first post. i only used the "RMS" figure to help make my point. i stated you can wire the higher powered sub to a lower ohm load to receive more power and vice versa. you could wire the "lower RMS" sub to a lower load and blow it if u wanted to. and when i did something like this i had 4 subs total at the time. i had 2 6.5" subs in Tapped horns, 1 10" sub in a sealed box, and a 15" sub in a really low tuned ported box. basicly the 6.5s played midbass and down to ~90hz, the sealed 10 played~90hz to ~35hz, and the ported 15 played 35hz and below. the crossover network was a pain in the ***, but total system power was only ~1K watts and it sounded **** good. and the phasing was basicly a non issue due to the crossover settup. there was some slight cancelation at each crossover point but a sinple EQ boost fixed that problem. :-) Matt [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Amplifiers
does the amplifier divide power.......
Top
Menu
Home
Refresh